We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular memory module with gold edge connector and black chips, no heat spreader

NEMIX RAM

NEMIX RAM 2GB DDR3 1333MHz PC3-10600 CL9 1.5V 240-Pin UDIMM desktop RAM

SKU CH-HK0C-M4363

A 2GB DDR3 desktop module running at 1333MHz with CL9 latency and 1.5V operation

  • Capacity2GB
  • Type240-Pin DDR3 UDIMM
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL9
  • Voltage1.50V
  • ECCNo
  • 2GB capacity adds responsive multitasking headroom
  • DDR3 1333MHz speed matches PC3-10600 system requirements
  • CL9 latency at 1.5V keeps timing tight and power low
  • 240-pin UDIMM fits standard desktop motherboards
  • Major OEM Samsung Micron Hynix chips ensure module reliability

2 GB DDR3 1333 UDIMM

This NEMIX RAM module provides 2 GB of DDR3 memory at 1333 MHz with CL9 latency. It uses a 240-pin unbuffered UDIMM form factor and runs at 1.5 V. The stick is built with major OEM chips from Samsung, Micron or Hynix and carries no heat spreader. It is intended for desktop systems that accept standard DDR3 UDIMM memory.

Check motherboard DDR3 slot and voltage

Verify that your motherboard has a free 240-pin DDR3 slot and supports 1.5 V unbuffered non-ECC modules at 1333 MHz. Consult the board manual for maximum capacity per slot and total system limit. The part is referenced as compatible with Dell A7075897, but compatibility with other systems must be confirmed against the motherboard specifications. No heat spreader means clearance is minimal.

Suits basic DDR3 desktop upgrades

This module suits users adding a single 2 GB stick to an older DDR3 desktop for light workloads or to meet a minimum memory requirement. It is not ECC or registered, so it will not work in platforms that require those features. Builders needing higher capacity, faster speeds, lower latency or registered memory should look at other modules.

Highlights

  • 2GB capacity adds responsive multitasking headroom
  • DDR3 1333MHz speed matches PC3-10600 system requirements
  • CL9 latency at 1.5V keeps timing tight and power low
  • 240-pin UDIMM fits standard desktop motherboards
  • Major OEM Samsung Micron Hynix chips ensure module reliability

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM DDR3 Orignial Desktop PC 240-Pin Non-ECC Unbuffered UDIMM Memory
ModelOriginal Series DDR3 Desktop PC Memory Solutions
Part NumberMD10600-228K1
Capacity2GB
Type240-Pin DDR3 UDIMM
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL9
Voltage1.50V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
FeaturesDDR3 Non-ECC Unbuffered UDIMM Motherboard Compatible
LED ColorNone

Questions about this item

Will this 240‑pin DDR3 module work in a motherboard that requires PC3‑10600 speed and CL9 timing?

Yes, the stick runs at 1333 MHz with PC3‑10600 rating and CL9 latency, matching those specifications exactly.

Does the 1.5 V operating voltage suit standard desktop boards without manual BIOS changes?

The module operates at the standard 1.5 V for DDR3, so most desktop motherboards will configure it automatically.

Is the non‑ECC, unbuffered design compatible with a Dell system that uses part A7075897?

The part is listed as compatible with Dell A7075897 and uses a non‑ECC, unbuffered layout that matches that requirement.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.