We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular DDR3 memory module with gold edge connectors and black chips on both sides

OWC

OWC 4GB DDR3 1600 CL11 240-pin UDIMM Dell OptiPlex XE2 SFF Tower

SKU CH-H4RC-R76XB

4GB DDR3 1600 CL11 UDIMM upgrade for Dell OptiPlex XE2 SFF and Tower systems

  • Capacity4GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • Boosts system responsiveness with a 4 GB DDR3 1600 MHz module
  • Meets OEM specifications through JEDEC and RoHS compliance
  • Fits Dell OptiPlex XE2 SFF and Tower with 240-pin UDIMM
  • Simple DIY upgrade using unbuffered non-ECC 1.5 V memory
  • Backed by lifetime warranty with free technical support

System-specific DDR3 upgrade for Dell OptiPlex

This OWC module adds 4GB of DDR3 1600 memory to a Dell OptiPlex XE2 SFF or XE2 Tower. It is a JEDEC-standard, non-ECC UDIMM that installs in a standard 240-pin desktop slot. The single rank 1Rx8 design runs at 1.5V with CL11 latency. It targets owners of those specific OptiPlex models who want a straightforward capacity increase.

Suits XE2 SFF and Tower owners.

The part is validated only for the Dell OptiPlex XE2 SFF and XE2 Tower. It will not help builders working on a different motherboard platform, a laptop, or any system that requires ECC or registered modules. Buyers with a different OptiPlex series or a workstation needing error correction should look elsewhere.

240-pin DDR3 UDIMM form factor decides fit

The module uses the 240-pin DDR3 UDIMM form factor, which physically matches the memory slots in the compatible OptiPlex XE2 systems. A motherboard that accepts only a different pin count, a different DDR generation, or a registered DIMM type cannot use this module. Verify the slot type before ordering.

Highlights

  • Boosts system responsiveness with a 4 GB DDR3 1600 MHz module
  • Meets OEM specifications through JEDEC and RoHS compliance
  • Fits Dell OptiPlex XE2 SFF and Tower with 240-pin UDIMM
  • Simple DIY upgrade using unbuffered non-ECC 1.5 V memory
  • Backed by lifetime warranty with free technical support

Specifications

BrandOWC
Part Number1U6D31R804GB
Capacity4GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex XE2 SFF
Dell OptiPlex XE2 Tower

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Will the 240-pin DDR3 UDIMM fit the Dell OptiPlex XE2 SFF chassis?

Yes, the 240-pin DDR3 UDIMM is the correct form factor for the Dell OptiPlex XE2 SFF and Tower systems listed in the compatibility data.

What is the correct way to seat the module so the clips lock on both ends?

Align the notch on the module with the slot key, press straight down firmly until both side clips snap into place with an audible click.

Does the module require any firmware updates or driver installation after fitting?

No firmware or driver is needed; the system BIOS detects the 4GB DDR3 1600 CL11 module automatically on first boot.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.