We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular circuit board with black memory chips and gold edge connector

OWC

OWC 8GB DDR4 2400 CL17 2Rx8 260-pin 1.2V Non-ECC SODIMM for NCR Kitchen Controller 5 (1925)

SKU CH-EW22-NK706

8GB DDR4 2400 CL17 SODIMM adds responsive memory to the NCR Kitchen Controller 5 (1925)

  • Capacity8GB
  • Type260-Pin DDR4 Non-ECC SODIMM
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.2V
  • ECCNo
  • Boost POS speed with 8 GB DDR4 2400 MHz module
  • Cut power draw using 1.2 V low-voltage design
  • Fit NCR Kitchen Controller 5 (1925) with 260-pin SODIMM
  • Meet OEM specs via JEDEC-standard 2Rx8 CL17 build
  • Enable easy DIY upgrade with unbuffered non-ECC layout

System-specific upgrade for NCR Kitchen Controller 5

This OWC module is a single 8 GB DDR4 2400 CL17 SODIMM built to the exact electrical and mechanical requirements of the NCR Kitchen Controller 5 (1925). It installs directly into the 260-pin slot without configuration changes and runs at the standard 1.2 V. The part is intended for operators who need the factory-validated capacity increase for that specific POS platform.

JEDEC and RoHS compliance with lifetime support

The stick meets JEDEC DDR4 standards and is RoHS compliant, so it qualifies as a warranty-safe upgrade for the controller. OWC backs it with a limited lifetime warranty and an advanced replacement programme that includes free technical support. No extra software, cables or adapters are bundled; the module itself is the complete upgrade kit.

8 GB capacity for single-slot headroom

One 8 GB rank delivers the maximum density this single SODIMM slot can accept, giving the controller enough memory for typical multi-application kitchen workloads. Systems that require more than 8 GB total or that use a different DDR generation, ECC, registered DIMMs or a 2133 MHz base speed without 2400 MHz support are not served by this part.

Highlights

  • Boost POS speed with 8 GB DDR4 2400 MHz module
  • Cut power draw using 1.2 V low-voltage design
  • Fit NCR Kitchen Controller 5 (1925) with 260-pin SODIMM
  • Meet OEM specs via JEDEC-standard 2Rx8 CL17 build
  • Enable easy DIY upgrade with unbuffered non-ECC layout

Specifications

BrandOWC
Part Number2S4D42R808GB
Capacity8GB
Type260-Pin DDR4 Non-ECC SODIMM
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemNCR POS Kitchen Controller 5 (1925)

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Will the 2Rx8 DDR4 module need replacing if the Kitchen Controller 5 later requires ECC memory?

This module is non-ECC and unbuffered. If the controller demands ECC registered memory, this stick cannot meet that requirement and would need to be swapped for an ECC variant.

What limit appears first when the SODIMM runs continuously at 2400 MHz in the Kitchen Controller 5?

The CL17 latency at 1.2 V sets the timing boundary; sustained loads hit the CAS latency ceiling before voltage or thermal throttling becomes a factor.

How much heat and power does the 8 GB stick produce during all-day operation?

At 1.2 V with no heat spreader, the module draws minimal power and runs cool; typical DDR4 SODIMM thermals stay well within the controller's passive cooling capacity.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.