We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green 288-pin DDR4 UDIMM module with black chips, no heat spreader

OWC

OWC 8GB DDR4 3200 CL22 UDIMM memory upgrade for Dell OptiPlex 3000 5000 5080

SKU CH-XVJQ-V06TA

Adds 8 GB of DDR4-3200 CL22 memory to Dell OptiPlex 3000, 5000 and 5080 desktops

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 3200 (PC4 25600)
  • CAS LatencyCL22
  • Voltage1.2V
  • ECCNo
  • 8GB capacity expands multitasking headroom for demanding workloads
  • DDR4 3200 speed with CL22 timing delivers responsive system performance
  • 2V operation reduces power draw and heat output
  • Validated for Dell OptiPlex 3000 5000 5080 SFF and Tower models
  • JEDEC compliant and ROHS certified for warranty safe upgrade

Compatible Dell OptiPlex DDR4 upgrade

This 8 GB DDR4 module is built for Dell OptiPlex 3000 SFF, 3000 Tower, 5000 SFF, 5000 Tower and 5080 SFF systems. It installs in a standard 288-pin UDIMM slot and runs at 1.2 V without ECC or buffering. The unbuffered design keeps installation straightforward for a DIY memory upgrade.

Replaces slower DDR4 or fills empty slots

The module operates at 3200 MHz with CL22 latency and is backward compatible with 2133 MHz, 2400 MHz, 2666 MHz and 2933 MHz buses. It upgrades systems running at those lower speeds or adds capacity when free DIMM slots are available. The jump is worthwhile when the platform supports 3200 MHz and the workload benefits from the higher data rate.

Limited to DDR4 UDIMM electrical

The memory uses the DDR4 UDIMM standard, so it fits only 288-pin unbuffered non-ECC slots at 1.2 V. It cannot be used in systems that require registered, load-reduced or ECC modules, nor in boards wired for other DDR generations. Maximum speed is capped by the memory controller and the slowest installed module.

Highlights

  • 8GB capacity expands multitasking headroom for demanding workloads
  • DDR4 3200 speed with CL22 timing delivers responsive system performance
  • 2V operation reduces power draw and heat output
  • Validated for Dell OptiPlex 3000 5000 5080 SFF and Tower models
  • JEDEC compliant and ROHS certified for warranty safe upgrade

Specifications

BrandOWC
Part Number3U2D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 3200 (PC4 25600)
CAS LatencyCL22
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 3000 SFF
Dell OptiPlex 3000 Tower
Dell OptiPlex 5000 SFF
Dell OptiPlex 5000 Tower
Dell OptiPlex 5080 SFF

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Does this 288-pin DDR4 UDIMM fit the Dell OptiPlex 3000 SFF and 5000 Tower?

Yes, it is built for the OptiPlex 3000 SFF, 3000 Tower, 5000 SFF, 5000 Tower and 5080 SFF. The 288-pin DDR4 form factor matches the desktop DIMM slots in those models.

What is the common mistake when installing this CL22 3200 MHz module?

Not seating the module until both retention clips click. Press down firmly on each end until the clips snap into the notches on the 288-pin edge connector.

Will the 1.2 V non-ECC 1Rx8 stick need replacement if I later add faster DDR4?

It runs at 3200 MHz CL22 and is backward compatible with 2133, 2400, 2666 and 2933 MHz. Mixing speeds works, but all modules will run at the slowest installed speed.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.