We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green printed circuit board with black memory chips and gold edge connectors

OWC

OWC 8GB DDR4 3200MHz CL22 1.2V 288-pin UDIMM for Dell OptiPlex 7080 7090 XE4

SKU CH-JT9E-KHZ8S

8GB DDR4 3200MHz CL22 UDIMM upgrades Dell OptiPlex 7080, 7090 and XE4 SFF and Tower systems with JEDEC-compliant 1.2V memory

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 3200 (PC4 25600)
  • CAS LatencyCL22
  • Voltage1.2V
  • ECCNo
  • Boosts multitasking with 8 GB DDR4 3200 MHz CL22
  • Low 1.2 V power draw cuts heat and energy use
  • Fits Dell OptiPlex 7080 SFF, Tower, 7090 SFF, Tower and XE4 SFF
  • JEDEC and RoHS compliant for a warranty-safe upgrade
  • Backward compatible with 2133, 2400, 2666 and 2933 MHz systems

Dell OptiPlex DDR4 Upgrade

This OWC module delivers 8 GB of DDR4 3200 memory for Dell OptiPlex 7080 and 7090 desktops plus the XE4 SFF. It targets owners of those specific systems who need a straightforward capacity increase. Builders working on other platforms or requiring ECC cannot use this stick.

JEDEC Voltage and Thermals

The module runs at the standard 1.2 V defined by JEDEC DDR4 specifications. Low voltage keeps power draw modest and heat output minimal inside small-form-factor chassis. No heat spreader is fitted, relying on case airflow for passive cooling.

Lifetime Warranty and Support

OWC backs the memory with a limited lifetime warranty and an advanced replacement programme. Free technical support is included for installation questions. No extra software or accessories are bundled with the DIMM.

Highlights

  • Boosts multitasking with 8 GB DDR4 3200 MHz CL22
  • Low 1.2 V power draw cuts heat and energy use
  • Fits Dell OptiPlex 7080 SFF, Tower, 7090 SFF, Tower and XE4 SFF
  • JEDEC and RoHS compliant for a warranty-safe upgrade
  • Backward compatible with 2133, 2400, 2666 and 2933 MHz systems

Specifications

BrandOWC
Part Number3U2D41R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 3200 (PC4 25600)
CAS LatencyCL22
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemDell OptiPlex 7080 SFF
Dell OptiPlex 7080 Tower
Dell OptiPlex 7090 SFF
Dell OptiPlex 7090 Tower
Dell OptiPlex XE4 SFF

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

How do I install the 288-pin UDIMM in my Dell OptiPlex 7080 and what step is often missed?

Power off the PC, unplug the mains lead, open the chassis, align the notch on the module with the slot key, press firmly until both retention clips click, then power on and verify the new 8GB appears in BIOS or Task Manager.

What maintenance or replacement will this DDR4 module need over its lifetime?

No scheduled maintenance is required; the module has no heat spreader or moving parts, so replacement is only necessary if a fault develops or you later upgrade to a higher capacity kit.

What limit appears first when this CL22 1.2V module runs under sustained load?

The CAS latency of 22 cycles at 3200MHz sets the timing ceiling; the module will not run tighter timings without exceeding the rated 1.2V specification.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.