We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Grey ATX power supply with 80mm fan, reduced depth 5.9 x 3.4 inches, 2.5kg

Replace Power

Replace Power RPSU-C99-2 ATX power supply 115/230V 80mm fan 2.5kg

SKU CH-KRVC-QP868 MPN RPSU-C99-2

ATX power supply with 80 mm fan, switchable 115/230 V input, SATA and ATX connectors, and reduced 5.9" depth for legacy HP Pavilion models

  • ColorGrey
  • TypeATX
  • Fans1
  • Weight2.5
  • Direct replacement for multiple HP Pavilion models
  • Switchable 115 / 230 V input suits global mains
  • Compact 5.9" depth eases fit in tight cases
  • 80 mm fan delivers active cooling under load
  • Over-current, over-power and over-voltage protection safeguards components

Direct Replacement for HP Pavilion Systems

This Replace Power RPSU-C99-2 ATX power supply is built as a direct replacement for specific HP Pavilion models including the a1511kr, a1512x, a1514n, a1517x, a1450n, a1467c and a1523w. It accepts 115 or 230 V input via a manual switch and uses a single 80 mm fan for cooling. The unit weighs 2.5 kg and measures 5.9 inches in height by 3.4 inches in width.

Restores Power to Legacy Desktops

It replaces an original supply that has failed or cannot support added components such as extra drives. The reduced depth improves fit inside compact HP chassis where standard ATX units may not seat properly. Over current, over power and over voltage protection circuits help safeguard the motherboard and attached peripherals. The upgrade is worth it when the original unit shows instability or lacks the connectors a newer configuration requires.

Straightforward Swap with Standard ATX Mounting

Installation follows a standard ATX mounting pattern using four screws at the rear of the case. The connector set includes one SATA, one 20+4 pin ATX, one 12 V ATX, two large peripheral plugs and one 6-inch small peripheral plug. The most common issue is forgetting to set the 110 V or 220 V switch to match the local mains voltage before powering on. Cable lengths are fixed, so verify reach to the motherboard and drive bays in the target chassis.

Highlights

  • Direct replacement for multiple HP Pavilion models
  • Switchable 115 / 230 V input suits global mains
  • Compact 5.9" depth eases fit in tight cases
  • 80 mm fan delivers active cooling under load
  • Over-current, over-power and over-voltage protection safeguards components

Specifications

BrandReplace Power
ModelRPSU-C99-2
ColorGrey
TypeATX
Fans1
Weight2.5

Questions about this item

Will the 5.9 inch height and 3.4 inch width fit my HP Pavilion a1511kr case?

The unit measures 5.9 inches high by 3.4 inches wide with a reduced depth design for increased compatibility in older HP Pavilion models including the a1511kr.

How do I set the 115/230V input switch correctly during installation?

Before connecting the ATX and 12V power cables, slide the voltage selector to 115V or 230V to match your local mains supply; the step most often missed is verifying the switch position after mounting.

When should I clean or replace the 80mm cooling fan?

Vacuum dust from the 80mm fan intake every six to twelve months; if bearing noise appears or airflow drops, replace the entire power supply as the fan is not user-serviceable.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.