A-Tech
A-Tech 32GB DDR4 2666MHz CL19 2Rx8 for Samsung M471A4G43MB1-CTD laptop RAM
A 32 GB DDR4 2666 MHz CL19 2Rx8 SODIMM replacement for Samsung M471A4G43MB1-CTD laptops
- Capacity32GB
- Type260-Pin DDR4 SO-DIMM
- SpeedDDR4 2666 (PC4 21300)
- CAS LatencyCL19
- Voltage1.20V
- ECCNo
- 32 GB capacity lets you run more apps at once
- 2666 MHz DDR4 speed moves data quickly through the system
- CL19 latency keeps response times tight
- 20 V operation matches standard laptop power limits
- 260-pin SO-DIMM form factor fits compatible notebook slots
32GB DDR4 2666MHz laptop module
This is a single 32GB DDR4 SO-DIMM running at 2666MHz with CL19 latency and 1.20V operation. The 260-pin unbuffered non-ECC stick is built as a direct replacement for the Samsung M471A4G43MB1-CTD part number.
Suits notebooks needing one 32GB stick
Buyers whose laptop has a single SO-DIMM slot and supports DDR4 2666MHz will gain the full 32GB capacity in one module. Systems limited to lower maximum memory per slot or requiring ECC registered memory should look at something else.
Simple press-in installation
Align the notch on the 260-pin edge connector with the slot key, insert at a slight angle, then press down until the side clips lock. The most common issue is the module not seating fully, which causes the laptop to fail POST or show no memory detected.
Pontos fortes
- 32 GB capacity lets you run more apps at once
- 2666 MHz DDR4 speed moves data quickly through the system
- CL19 latency keeps response times tight
- 20 V operation matches standard laptop power limits
- 260-pin SO-DIMM form factor fits compatible notebook slots
Especificações
| Brand | A-Tech |
|---|---|
| Capacity | 32GB |
| Type | 260-Pin DDR4 SO-DIMM |
| Speed | DDR4 2666 (PC4 21300) |
| CAS Latency | CL19 |
| Voltage | 1.20V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Recommend Use | AMD & Intel Compatible |
Perguntas sobre este artigo
My laptop only has one SO-DIMM slot — will this single 32GB module work on its own?
Yes, this is a single 32GB DDR4 2666MHz CL19 module that runs at 1.20V and fits a standard 260-pin slot, so it operates independently without needing a second stick.
I plan to keep my existing DDR4 2666MHz stick in the second slot — will both modules run together at 2666MHz?
If the existing stick is also DDR4 2666MHz CL19 at 1.20V unbuffered non-ECC, the system will run both at 2666MHz; mixing different speeds or latencies forces the faster module down to the slower one.
After installing the module, how can I confirm it is running at 2666MHz with CL19 timings?
Open Task Manager → Performance → Memory or run CPU-Z; the speed should show 2666MHz (PC4-21300) and the CAS latency should read 19 when the system is under load.
Também nesta secção
Os clientes também compararam
Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.
Mushkin Enhanced 4GB DDR2-800 CL6 SoDIMM Apple 971741A memory upgrade
SK hynix HYMD232M646C6-J 256MB DDR 333MHz PC2700 CL2.5 SODIMM laptop RAM
- 4GB (2 x 2GB)



