BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 US$
0.00277131BTC
Em stock
NEMIX RAM
NEMIX RAM 64GB (4x16GB) DDR5 5600 CL46 1.1V 288-Pin UDIMM Dell Pro Max Tower T2
64GB kit of four 16GB DDR5 UDIMM modules at 5600MHz CL46 1.1V for Dell Pro Max Tower T2
- Capacity64GB (4 x 16GB)
- SpeedDDR5 5600 (PC5 44800)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.10V
- 64 GB total capacity across four 16 GB modules
- DDR5 5600 speed rated at PC5-44800 bandwidth
- CL46 CAS latency for responsive system performance
- 1 V low-voltage operation reduces power draw
- Designed specifically for Dell Pro Max Tower T2 desktop
Dell Pro Max Tower T2 Compatible Kit
This 64 GB kit is built specifically for the Dell Pro Max Tower T2 desktop. It contains four 16 GB modules that install directly into the system's DDR5 slots. The memory targets owners who need a straightforward capacity increase for demanding workloads on this exact platform.
Low-Voltage DDR5 Operation
Each module runs at 1.10 V with a CL46 latency rating at the DDR5 5600 standard. The unbuffered, non-ECC design draws minimal power while maintaining stable throughput for everyday multitasking and professional applications. No heat spreaders are fitted, so airflow around the DIMMs handles thermal management.
Four-Module Population
The kit fills four UDIMM sockets with 1Rx8 organisation, leaving no empty slots for future expansion on a typical four-slot board. Installation follows the standard 288-pin DDR5 keying and requires no additional cables or configuration beyond the system firmware. Builders planning larger arrays should verify the platform's maximum supported capacity before purchase.
Pontos fortes
- 64 GB total capacity across four 16 GB modules
- DDR5 5600 speed rated at PC5-44800 bandwidth
- CL46 CAS latency for responsive system performance
- 1 V low-voltage operation reduces power draw
- Designed specifically for Dell Pro Max Tower T2 desktop
Especificações
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Memory |
| Model | DDR5 Non-ECC Unbuffered UDIMM Memory |
| Part Number | MD44800-618K4 |
| Capacity | 64GB (4 x 16GB) |
| Speed | DDR5 5600 (PC5 44800) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.10V |
| Compatible System | Dell |
| CAS Latency | CL46 |
| Heat Spreader | No |
| Type | 288-Pin DDR5 UDIMM |
| Rank | 1Rx8 |
| Features | DDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible |
| Package Content | 64GB (4 x 16GB) DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT |
Perguntas sobre este artigo
How do I install the four 16 GB DDR5 UDIMMs in the Dell Pro Max Tower T2 and which slot order do people often get wrong?
Power off the Dell Pro Max Tower T2, open the case, align each 288-pin module with the keyed slot and press firmly until the retention clips click; the manual specifies populating the four slots in the labelled sequence so the memory controller trains all 64 GB at 5600 MT/s.
What maintenance or replacement will the NEMIX RAM kit need during its service life?
The modules have no heat spreaders and run at 1.10 V, so only occasional dust removal from the slots is required; if a stick fails the lifetime replacement warranty covers a direct swap of the defective 16 GB UDIMM.
What limit appears first when the 64 GB DDR5 5600 CL46 kit runs sustained workloads on the Dell Pro Max Tower T2?
The CAS latency of CL46 at 5600 MT/s sets the timing boundary; under continuous load the memory controller hits this latency ceiling before thermal or voltage limits become a factor.
Também nesta secção
Os clientes também compararam
Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.
BFKK
BFKK 2U Micro ATX Rackmount 2×5.25" 4×3.5" Side 80mm Fan
- Rackmount
216,99 US$
0.00279709BTC
Em stock
