Aceitamos criptomoeda — para que as moedas que detém possam comprar material informático real.Pague em cripto, gaste-a em material informático real. Envio seguro gratuito para todo o mundo acima de 399 $. Caixas neutras, sem marca, expedidas a partir da Alemanha.Envio seguro gratuito acima de 399 $. A sua taxa fica bloqueada durante 30 minutos assim que abre a finalização da compra.Taxa bloqueada 30 minutos. Cada artigo é selado, o seu número de série é verificado, e está coberto por uma garantia de 24 meses.Selado, garantido 24 meses.

Artigos guardados Iniciar sessão
Green bare circuit board with gold contacts and black memory chips

OWC

OWC 64GB DDR4 3200 CL22 2Rx4 288-pin 1.2V ECC Registered RDIMM memory upgrade

SKU CH-602B-Z0JZV

A 64GB DDR4 3200 ECC registered RDIMM module for Supermicro H12SSL, H12SSW and X12DPG server boards

  • Capacity64GB
  • Type288-Pin DDR4 ECC RDIMM
  • SpeedDDR4 3200 (PC4 25600)
  • CAS LatencyCL22
  • Voltage1.2V
  • ECCYes

Capacity 64GB

As versões riscadas existem, mas não estão disponíveis aqui.

  • 64 GB capacity lets you run large workloads on supported Supermicro boards
  • ECC registered design detects and corrects data errors for server reliability
  • DDR4 3200 speed with CL22 latency delivers rated throughput
  • Single 2Rx4 module simplifies upgrades without mixing ranks
  • 2 V operation meets JEDEC standard for efficient power use

Server Memory Upgrade

This OWC module is a single 64GB DDR4 3200 ECC Registered RDIMM designed for specific Supermicro motherboards including H12SSL-CT, H12SSL-NT, H12SSW-iNR, H12SSW-NTR and X12DPG-OA. It targets administrators upgrading workstation or server platforms that require registered error-correcting memory. It is not for standard desktop computers or systems needing unbuffered or load-reduced DIMMs.

Registered ECC Requirement

The decisive specification is the registered ECC design with 2Rx4 organisation, which only functions in motherboards wired for registered modules. Mixing this stick with unbuffered or load-reduced memory will prevent the system from posting. Buyers must verify their board explicitly supports registered ECC DDR4 before purchasing.

Straightforward Slot Installation

Installation follows the standard 288-pin DIMM procedure: align the notch, press firmly until the retention clips engage, then power on. The most common issue is seating the module incompletely, which causes boot failures or memory errors. Because registered DIMMs place a heavier electrical load on the memory controller, populating every slot may require a BIOS update for full stability.

Pontos fortes

  • 64 GB capacity lets you run large workloads on supported Supermicro boards
  • ECC registered design detects and corrects data errors for server reliability
  • DDR4 3200 speed with CL22 latency delivers rated throughput
  • Single 2Rx4 module simplifies upgrades without mixing ranks
  • 2 V operation meets JEDEC standard for efficient power use

Especificações

BrandOWC
Part Number3R2D42R464GB
Capacity64GB
Type288-Pin DDR4 ECC RDIMM
SpeedDDR4 3200 (PC4 25600)
CAS LatencyCL22
Voltage1.2V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
Heat SpreaderNo
Compatible SystemSupermicro Motherboard H12SSL-CT
Supermicro Motherboard H12SSL-NT
Supermicro Motherboard H12SSW-iNR
Supermicro Motherboard H12SSW-NTR
Supermicro Motherboard X12DPG-OA

Outras versões deste modelo

Mais 5 nesta gama

Mesma família, memória, ventoinha ou frequência diferentes — compare antes de decidir.

Perguntas sobre este artigo

What does the 3200 speed rating mean once the module is installed in a Supermicro board?

The DDR4 3200 module runs at up to 3200 MT/s when the motherboard memory controller supports that data rate; the actual operating speed is set by the platform firmware.

What does the PC4-25600 designation tell me about the interface and its practical limit?

PC4-25600 is the JEDEC standard name for DDR4 3200, confirming the module meets the 3200 MT/s specification and 1.2 V operation defined for that speed grade.

What physical slot and clearance does this 288-pin RDIMM need to fit?

It requires a standard 288-pin DDR4 DIMM socket; the registered design adds a buffer chip so the module will only work in boards wired for registered ECC memory such as the listed Supermicro models.

Também nesta secção

Os clientes também compararam

Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.