Aceitamos criptomoeda — para que as moedas que detém possam comprar material informático real.Pague em cripto, gaste-a em material informático real. Envio seguro gratuito para todo o mundo acima de 399 $. Caixas neutras, sem marca, expedidas a partir da Alemanha.Envio seguro gratuito acima de 399 $. A sua taxa fica bloqueada durante 30 minutos assim que abre a finalização da compra.Taxa bloqueada 30 minutos. Cada artigo é selado, o seu número de série é verificado, e está coberto por uma garantia de 24 meses.Selado, garantido 24 meses.

Artigos guardados Iniciar sessão
Small black 50mm centrifugal blower fan with two-pin connector

SXDOOL

SXDOOL 5015 50mm Blower Fan 24V 1.11W Double Ball Bearing

SKU CH-7H5R-3FZD5

A 50 mm centrifugal blower delivers 4.2 CFM at 5800 RPM for 3D-printer hot-end cooling

  • TypeCase Fan
  • Fan Size50mm
  • Bearing TypeBall
  • Power Connector2 Pin
  • ColorBlack
  • LEDNon-LED
  • 5800 RPM centrifugal airflow cools hot-ends fast
  • Double ball bearing extends service life
  • 11 W at 24 V keeps power draw low
  • 3 dBA noise suits quiet workspaces
  • 50 × 50 × 15 mm fits standard 5015 mounts

Targeted cooling for 3D printers

The SXDOOL 5015 is a 50 mm centrifugal blower built for 3D printer hot-ends and similar tight spaces. It runs on 24 V DC and draws only 1.11 W, making it suitable for low-voltage printer electronics. The double ball bearing is rated for extended service life under continuous operation. A two-pin power connector keeps wiring simple for direct board connection.

Thermals noise and power draw

At 5800 RPM the fan moves 4.2 CFM with a static pressure of 0.52 inch-H₂O, enough to push air through restrictive ducts. Acoustic output is specified at 43.3 dBA under normal load. The low 1.11 W power draw minimises heat added to the printer enclosure. Dual ball bearings help maintain consistent speed and noise levels over time.

Build quality and daily fit

The compact 50 x 50 x 15 mm housing weighs just 30 g, so it adds minimal mass to moving gantries. Black non-LED housing blends into most printer frames without light bleed. Two-pin connector polarity must be observed during installation. The turbine outlet directs airflow perpendicular to the intake, requiring a matching duct design for best results.

Pontos fortes

  • 5800 RPM centrifugal airflow cools hot-ends fast
  • Double ball bearing extends service life
  • 11 W at 24 V keeps power draw low
  • 3 dBA noise suits quiet workspaces
  • 50 × 50 × 15 mm fits standard 5015 mounts

Especificações

TypeCase Fan
Fan Size50mm
Bearing TypeBall
Power Connector2 Pin
ColorBlack
LEDNon-LED

Perguntas sobre este artigo

How do I install the SXDOOL 5015 blower fan and what step do people often miss?

Mount the 50mm turbine fan using its 50×50×15 mm frame, connect the 2-pin header to a 24 V DC source, and verify airflow direction — the centrifugal exhaust must face the hotend, not away from it.

What maintenance or replacement will the double ball bearing fan need later?

The dual ball bearings are rated for long service life; expect only occasional dust removal from the impeller blades, and replace the unit if RPM drops well below 5800 or noise rises above 43.3 dBA.

What limit appears first during sustained 24 V operation?

Continuous running at 5800 RPM with 0.52 inch-H₂O pressure and 4.2 CFM flow keeps the motor at its 1.11 W thermal ceiling; exceeding the rated voltage or blocking the exhaust will hit that thermal limit first.

Também nesta secção

Os clientes também compararam

Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.