我們接受加密貨幣付款 — 讓您持有的幣種也能買到真正的硬體設備。以加密貨幣付款，直接購入真正的硬體設備。 全球訂單滿 US$399，即享免費保險運送。簡約外箱，不印任何品牌標誌，從德國出貨。訂單滿 US$399，即享免費保險運送。 結帳一開始，您的匯率即鎖定 30 分鐘。匯率鎖定 30 分鐘。 每件商品皆原廠密封、序號經過核對，並享有 24 個月保固。原廠密封，保固 24 個月。

追蹤清單 登入
Silver 3.5 inch SCSI hard drive with 80 pin connector

Seagate

Seagate ST32171WC Barracuda 2.16GB 7200RPM 512KB Ultra 80Pin 3.5" SCSI internal hard drive

SKU CH-2YTA-134QJ

A 2.16 GB, 7200 RPM SCSI hard drive with a 512 KB buffer and 80-pin connector

  • 16 GB capacity stores operating system and core applications
  • 7200 RPM spindle speed delivers responsive data access for legacy desktops
  • 512 KB cache buffers frequent read requests to reduce latency
  • Ultra SCSI 80-pin interface integrates directly into vintage server backplanes
  • 5 inch form factor fits standard drive bays in period-correct builds

2.16 GB SCSI drive for legacy systems

This 2.16 GB Seagate Barracuda drive uses a 3.5 inch SCSI Ultra interface with an 80-pin connector. It spins at 7200 RPM and provides a 512 KB buffer. The unit is supplied as a bare drive only.

Replaces slower narrow SCSI disks

The Ultra SCSI interface doubles the bus width compared with older narrow implementations, raising the theoretical transfer ceiling. The jump is worthwhile when a server or workstation backplane already supports wide Ultra SCSI and needs additional low-capacity spindles.

Fits 3.5 inch wide Ultra SCSI backplanes

Installation requires an 80-pin hot-plug backplane that supplies both power and signal through the single connector. No separate power cable is used. The drive adds one spindle to arrays or enclosures built for the Ultra wide standard.

商品特色

  • 16 GB capacity stores operating system and core applications
  • 7200 RPM spindle speed delivers responsive data access for legacy desktops
  • 512 KB cache buffers frequent read requests to reduce latency
  • Ultra SCSI 80-pin interface integrates directly into vintage server backplanes
  • 5 inch form factor fits standard drive bays in period-correct builds

商品規格

本商品目前尚未公佈規格。

商品問答

Will the 80-pin SCSI connector on this 3.5-inch drive fit my backplane?

The drive uses an 80-pin SCA-2 connector that combines power and data; it plugs directly into a hot-swap backplane or an 80-to-68-pin adapter for standard cables.

How do I set the SCSI ID so the host adapter sees the drive?

Use the three jumpers on the rear of the unit to select ID 0 through 7; the most common mistake is leaving all jumpers off, which defaults to ID 0 and can conflict with the host adapter.

What should I expect to replace on a 7200 RPM SCSI drive of this vintage?

The spindle motor bearings and actuator assembly are the parts that wear out; listen for new whining or clicking noises as early warning signs.

同類商品

顧客也比較過

同一分類，同一套結帳流程 — 支援八種加密貨幣，匯率鎖定 30 分鐘。