نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.

قائمة الرصد تسجيل الدخول
Atermiter AT-X99 motherboard with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC RAM installed

Atermiter

Atermiter AT-X99 embedded solution with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC

SKU CH-YW4W-0R2W1 MPN AT-X99

Embedded X99 motherboard kit with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC memory

  • CPU Socket TypeLGA 2011-v3
  • CPU TypeIntel Core 5th gen (LGA 2011-v3)

Option X99-2670V3-32GB 3200Mhz(16GB x 2pcs ECC)

  • Pre-configured Xeon E5-2670 V3 with 32 GB REG ECC
  • 32 GB DDR4 3200 MHz memory runs at CPU-limited 2133 MHz
  • Embedded X99 board fits 235 × 185 mm footprint
  • Four DDR4 slots allow ECC-only or UDIMM-only populations
  • 24-pin plus 8-pin power inputs for stable delivery

Ready-to-run Xeon workstation base

The Atermiter AT-X99 bundle pairs an Intel Xeon E5-2670 V3 with 32 GB of DDR4 REG ECC memory on an LGA 2011-v3 board. It arrives assembled and tested so system integrators and lab builders can deploy a validated compute node without sourcing separate components. The combination targets workloads that benefit from registered ECC stability such as rendering farms, simulation clusters or virtualization hosts.

Sustained-load behaviour with registered ECC

Under continuous load the Xeon E5-2670 V3 runs its cores at the processor's rated frequencies while the memory controller limits the 3200 MHz modules to 2133 MHz. The registered ECC design detects and corrects single-bit errors in real time, preventing silent data corruption during multi-day compute jobs. Thermal output remains consistent because the chipset and voltage regulation are sized for the supported 2011-v3 series rather than burst-only operation.

Upgrade path from consumer or mixed-memory builds

This kit replaces a consumer desktop platform that cannot accept registered ECC modules or a mixed-memory configuration the board forbids. The jump is worth it when the workload demands error-correcting memory across all four slots and a validated Xeon rather than a desktop CPU on a workstation chipset. Builders who need non-ECC UDIMM populations or a different chipset feature set should look elsewhere.

أبرز المميزات

  • Pre-configured Xeon E5-2670 V3 with 32 GB REG ECC
  • 32 GB DDR4 3200 MHz memory runs at CPU-limited 2133 MHz
  • Embedded X99 board fits 235 × 185 mm footprint
  • Four DDR4 slots allow ECC-only or UDIMM-only populations
  • 24-pin plus 8-pin power inputs for stable delivery

المواصفات

CPU Socket TypeLGA 2011-v3
CPU TypeIntel Core 5th gen (LGA 2011-v3)

إصدارات أخرى من هذا الطراز

3 أخرى من الفئة نفسها

نفس الفئة، بذاكرة أو مبرّد أو تردد مختلف — قارن قبل أن تقرر.

أسئلة حول هذا المنتج

How much heat and noise should I expect from the Xeon E5-2670 V3 running continuously on this board?

The board uses a 24-pin plus 8-pin power connection to feed the CPU and memory; sustained load will draw substantial current, so a chassis with good airflow and a cooler rated for high-wattage LGA 2011-v3 processors is essential.

What other parts do I need to have on hand before this embedded solution will boot?

You must supply a graphics card for the PCI-E x16 slot, storage drives, a case that fits the 235 mm by 185 mm board, and a PSU with both 24-pin and 8-pin CPU connectors.

Will my existing DDR4 UDIMM sticks work alongside the supplied 32 GB REG ECC kit?

The board cannot mix ECC and non-ECC modules; all four slots must use the same type, so you would need to replace any UDIMM sticks with REG ECC memory.

أيضًا في هذا القسم

عملاء قارنوا هذه المنتجات

نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.