BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
نقبل الدفع بالعملة المشفرة — لذلك يمكن للعملات الرقمية التي تملكها أن تشتري أجهزة حقيقية.ادفع بالعملة المشفرة، وأنفقها على أجهزة حقيقية. شحن مؤمن مجانا إلى كل أنحاء العالم لما يتجاوز 399 US$. صناديق شحن بسيطة بلا علامة تجارية، ترسل من ألمانيا.شحن مؤمن مجانا لما يتجاوز 399 US$. يُقفل سعرك لمدة 30 دقيقة بمجرد فتح صفحة الدفع.السعر مقفل لمدة 30 دقيقة. كل قطعة مختومة، ورقمها التسلسلي متحقق منه، ومشمولة بضمان 24 شهرا.مختوم، وبضمان 24 شهرا.
NEMIX RAM
A 16 GB dual-channel DDR5 kit running at 4800 MHz with CL40 latency and 1.1 V operation
This NEMIX RAM kit supplies 16 GB across two 8 GB DDR5 modules rated at 4800 MHz with CAS latency 40. The unbuffered non-ECC design suits desktop platforms that accept standard UDIMMs and do not require registered memory. Builders adding capacity to a compatible DDR5 system will find the dual-channel pair straightforward to install.
Each module runs at 1.1 V and uses the 288-pin DDR5 form factor, so the kit fits motherboards wired for this generation without extra power adapters. The 1Rx8 organisation leaves room for additional modules on boards with four slots, and the low voltage helps keep thermal headroom available for other components.
The kit replaces slower DDR5 memory or smaller capacity pairs when the platform supports 4800 MHz operation and non-ECC UDIMMs. The jump is worthwhile when the motherboard and processor can run at the rated speed, delivering higher bandwidth than lower-frequency DDR5 alternatives. Systems locked to registered or ECC-only memory cannot use this kit.
| Brand | NEMIX RAM |
|---|---|
| Model | Part#: MD38400-818K2-SM-SYS-111AD-HN2-01-G2 |
| Part Number | Part#: MD38400-818K2-SM-SYS-111AD-HN2-01-G2 |
| Capacity | 16GB (2 x 8GB) |
| Speed | DDR5 4800 (PC5 38400) |
| CAS Latency | 40 |
| Voltage | 1.1V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
The CL40 timing is the JEDEC standard for DDR5 4800 and sets the base response speed; tighter timings would require modules rated for lower latency at this frequency.
At 1.1 V the kit runs at the standard DDR5 voltage, so power consumption and thermals stay within normal limits for continuous use without extra cooling.
Yes, the board needs a 288-pin DDR5 DIMM socket and must accept non-ECC unbuffered memory; the 1Rx8 organisation also requires compatible memory-controller support.
أيضًا في هذا القسم
نفس القسم، ونفس صفحة الدفع — ثماني عملات رقمية وقفل سعر لمدة 30 دقيقة.
ما تدفعه، وما تُعرض به الأسعار.
يُرسَل من محفظتك عند إتمام الطلب
للعرض فقط — أسعار الكتالوج بالدولار الأمريكي
لا توجد عملة مطابقة.
اختر اللغة التي يخاطبك بها الموقع.
لا توجد لغة مطابقة.
هل أنت جديد هنا؟
لديك حساب بالفعل؟
لا توجد إعادة تعيين تلقائية: هذا المتجر لا يُرسل أي بريد، فلا يوجد رابط لمرة واحدة يمكن طلبه. اترك العنوان في الحساب، وسيُعالَج الأمر يدويًا.
تم تسجيل الطلب
لا شيء في طريقه إلى بريدك الوارد — هذا المتجر لا يُرسل أي بريد إطلاقًا. يتولّى أحدهم معالجة هذه الطلبات يدويًا.
تذكّرتها؟