Aceptamos criptomonedas — así, las criptos que usted tiene pueden comprar hardware real.Pague en cripto y gástela en hardware real. Envío asegurado gratis a nivel mundial a partir de $399. Cajas neutras, sin marca, enviadas desde Alemania.Envío asegurado gratis a partir de $399. Su cotización queda bloqueada 30 minutos en cuanto se abre el pago.Cotización bloqueada 30 minutos. Todos los artículos vienen sellados, con el número de serie verificado y cubiertos por una garantía de 24 meses.Sellado, con 24 meses de garantía.

Artículos guardados Iniciar sesión
Green rectangular circuit board with gold edge connector and black memory chips, no heat spreader

OWC

OWC 8GB DDR4 2400MHz CL17 1.2V 260-pin SODIMM for HP ProDesk 400 G3 Mini 600 G3 Mini

SKU CH-81EX-0JMCR

8GB DDR4 2400MHz CL17 SODIMM upgrades HP ProDesk 400 G3 Mini and 600 G3 Mini systems

  • Capacity8GB
  • Type260-Pin DDR4 Non-ECC SODIMM
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.2V
  • ECCNo
  • Boosts system responsiveness with 8GB DDR4 2400MHz speed
  • Low 1.2V voltage cuts power draw and heat
  • CL17 latency ensures quick data access for multitasking
  • JEDEC compliant for reliable HP ProDesk 400 G3 Mini and 600 G3 Mini fit
  • 260-pin SODIMM form factor enables straightforward DIY installation

8GB DDR4 SODIMM for HP ProDesk Mini

This 8GB DDR4 module is built specifically for the HP ProDesk 400 G3 Mini and 600 G3 Mini. It uses a 260-pin SODIMM form factor that fits the compact chassis of these systems. The kit targets owners of these exact models who need a straightforward memory increase.

Upgrade from lower capacity or slower DDR4

The module replaces an existing stick or fills an empty slot to raise total memory. It runs at 2400MHz with CL17 timing and 1.2V voltage. The jump is worth it when the current configuration limits multitasking or forces excessive paging on these supported platforms.

Limited by DDR4 SODIMM speed ceiling

The DDR4 2400 standard caps the data rate at 2400MHz, so this module cannot exceed that ceiling. It is backwards compatible with 2133MHz operation if the system requires it. Builders needing higher bandwidth or a different form factor cannot use this part.

Puntos fuertes

  • Boosts system responsiveness with 8GB DDR4 2400MHz speed
  • Low 1.2V voltage cuts power draw and heat
  • CL17 latency ensures quick data access for multitasking
  • JEDEC compliant for reliable HP ProDesk 400 G3 Mini and 600 G3 Mini fit
  • 260-pin SODIMM form factor enables straightforward DIY installation

Especificaciones

BrandOWC
Part Number2S4D41R808GB
Capacity8GB
Type260-Pin DDR4 Non-ECC SODIMM
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ProDesk 400 G3 Mini
HP ProDesk 600 G3 Mini

Otras versiones de este modelo

5 más en esta gama

Misma familia, con memoria, disipador o frecuencia diferentes — compare antes de decidirse.

Preguntas sobre este artículo

Will the 260-pin SODIMM fit inside the HP ProDesk 400 G3 Mini chassis?

Yes, the module is a 260-pin DDR4 SODIMM designed for the HP ProDesk 400 G3 Mini and 600 G3 Mini, matching the slot and 1.2V power requirement of those systems.

What is the correct way to seat the module so it locks in place?

Align the notch on the 260-pin edge connector with the key in the slot, insert at a slight angle, then press down firmly until the side clips click — the step often missed is pressing evenly on both ends until both clips engage.

Does this 8GB DDR4 2400MHz CL17 module need any firmware updates or periodic replacement?

No firmware is required; the JEDEC-compliant DDR4 SODIMM runs at 1.2V with CL17 timing and is rated for the life of the system, so no scheduled replacement is needed.

También en este pasillo

Los clientes también compararon

Mismo estante, mismo pago — ocho criptomonedas y un tipo de cambio fijado 30 minutos.