저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Four green DDR5 UDIMM sticks without heat spreaders

NEMIX RAM

NEMIX RAM 32GB (4x8GB) DDR5 5600 CL46 1.1V UDIMM for Supermicro X13SAW-F

SKU CH-DNBJ-9Z1AP

A 32 GB kit of four 8 GB DDR5 modules running at 5600 MT/s with CL46 latency and 1.1 V for the Supermicro X13SAW-F motherboard

  • Capacity32GB (4 x 8GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 32GB 4X8GB

  • 32 GB capacity across four 8 GB modules for expanded multitasking headroom
  • DDR5 5600 speed with CL46 latency delivers rated bandwidth for the platform
  • 1 V operation matches the board's memory-controller specification exactly
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F DIMM slots
  • Built with major OEM chips from Samsung, Micron or Hynix for tested stability

Exact-fit DDR5 kit for Supermicro X13SAW-F

This 32 GB kit provides four 8 GB DDR5 UDIMMs rated at 5600 MT/s with CL46 latency and 1.10 V operation. The modules use 1Rx8 non-ECC unbuffered chips from major OEM suppliers and match the 288-pin layout the motherboard requires.

Replaces mismatched or slower DDR5 modules

When a system shows reduced capacity or runs at lower speeds because of mixed ranks or voltages, this kit restores the full 32 GB at the board's native 5600 MT/s rating. The jump is worth it if the current memory does not meet the exact 1Rx8, 1.10 V, CL46 specification.

Suits builders populating all four slots

Buyers who need ECC error correction, registered modules, SODIMM form factor, or a different speed grade should look elsewhere. This kit is built only for non-ECC unbuffered desktop configurations that accept the stated timing and voltage.

주요 특징

  • 32 GB capacity across four 8 GB modules for expanded multitasking headroom
  • DDR5 5600 speed with CL46 latency delivers rated bandwidth for the platform
  • 1 V operation matches the board's memory-controller specification exactly
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F DIMM slots
  • Built with major OEM chips from Samsung, Micron or Hynix for tested stability

사양

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K4
Capacity32GB (4 x 8GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB 4X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

이 모델의 다른 버전

같은 라인업에서 5개 더

같은 제품군에서 메모리·쿨러·클럭이 다릅니다 — 결정 전에 비교해 보세요.

이 상품에 대한 질문

Will the 288-pin DDR5 UDIMM modules fit the Supermicro X13SAW-F motherboard slots?

Yes, the kit uses the 288-pin DDR5 UDIMM form factor that the X13SAW-F requires, so each module seats directly in the board's standard DIMM sockets.

What is the correct order to populate the four 8GB modules on the X13SAW-F?

Install the modules in the exact slot sequence shown in the Supermicro X13SAW-F manual; the board's memory-population rules determine which channels activate first and must be followed for all four sticks to be recognised.

Do these non-ECC UDIMMs need any firmware updates or driver installation after fitting?

No firmware or driver is required; the modules run at the rated DDR5 5600 CL46 1.1V settings once the system boots, provided the motherboard BIOS is current enough to support the memory controller.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.