暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Four green DDR5 UDIMM sticks without heat spreaders

NEMIX RAM

NEMIX RAM 32GB (4x8GB) DDR5 5600 CL46 1.1V UDIMM for Supermicro X13SAW-F

SKU CH-DNBJ-9Z1AP

A 32 GB kit of four 8 GB DDR5 modules running at 5600 MT/s with CL46 latency and 1.1 V for the Supermicro X13SAW-F motherboard

  • Capacity32GB (4 x 8GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 32GB 4X8GB

  • 32 GB capacity across four 8 GB modules for expanded multitasking headroom
  • DDR5 5600 speed with CL46 latency delivers rated bandwidth for the platform
  • 1 V operation matches the board's memory-controller specification exactly
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F DIMM slots
  • Built with major OEM chips from Samsung, Micron or Hynix for tested stability

Exact-fit DDR5 kit for Supermicro X13SAW-F

This 32 GB kit provides four 8 GB DDR5 UDIMMs rated at 5600 MT/s with CL46 latency and 1.10 V operation. The modules use 1Rx8 non-ECC unbuffered chips from major OEM suppliers and match the 288-pin layout the motherboard requires.

Replaces mismatched or slower DDR5 modules

When a system shows reduced capacity or runs at lower speeds because of mixed ranks or voltages, this kit restores the full 32 GB at the board's native 5600 MT/s rating. The jump is worth it if the current memory does not meet the exact 1Rx8, 1.10 V, CL46 specification.

Suits builders populating all four slots

Buyers who need ECC error correction, registered modules, SODIMM form factor, or a different speed grade should look elsewhere. This kit is built only for non-ECC unbuffered desktop configurations that accept the stated timing and voltage.

特長

  • 32 GB capacity across four 8 GB modules for expanded multitasking headroom
  • DDR5 5600 speed with CL46 latency delivers rated bandwidth for the platform
  • 1 V operation matches the board's memory-controller specification exactly
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F DIMM slots
  • Built with major OEM chips from Samsung, Micron or Hynix for tested stability

仕様

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K4
Capacity32GB (4 x 8GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB 4X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

Will the 288-pin DDR5 UDIMM modules fit the Supermicro X13SAW-F motherboard slots?

Yes, the kit uses the 288-pin DDR5 UDIMM form factor that the X13SAW-F requires, so each module seats directly in the board's standard DIMM sockets.

What is the correct order to populate the four 8GB modules on the X13SAW-F?

Install the modules in the exact slot sequence shown in the Supermicro X13SAW-F manual; the board's memory-population rules determine which channels activate first and must be followed for all four sticks to be recognised.

Do these non-ECC UDIMMs need any firmware updates or driver installation after fitting?

No firmware or driver is required; the modules run at the rated DDR5 5600 CL46 1.1V settings once the system boots, provided the motherboard BIOS is current enough to support the memory controller.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。