We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular circuit board with black memory chips and gold contacts along the bottom edge

A-Tech

A-Tech 16GB DDR4 2400MHz ECC UDIMM 2Rx8 CL17 1.2V Server Memory

SKU CH-12W8-TSTGP

16 GB DDR4 2400 MHz ECC UDIMM module with CL17 latency and 1.2 V operation

  • Capacity16GB
  • SpeedDDR4 2400 (PC4 19200)
  • CAS LatencyCL17
  • Voltage1.20V
  • ECCYes
  • Buffered/RegisteredUnbuffered
  • 16GB DDR4 2400MHz ECC UDIMM for server reliability
  • CL17 latency and 1.20V operation for stable performance
  • 2Rx8 dual-rank design increases memory density
  • 288-pin DIMM fits standard DDR4 server slots
  • Compatible replacement for Dell A9755388, A9755661 and CX1KM

16GB DDR4 2400 ECC UDIMM for Servers

This 16GB DDR4 2400 ECC UDIMM module provides error-correcting memory for server and workstation platforms that require 288-pin DIMMs. It operates at 1.2V with a CL17 latency and uses a 2Rx8 organisation. The unbuffered design fits systems that do not accept registered modules.

Replaces Dell A9755388 and A9755661 Part Numbers

This module is a compatible equivalent for Dell part numbers including A9755388, A9755661, CX1KM, SNPCX1KMC/16G, SNPCX1KMDG/16G, and YXC0V. The upgrade is worthwhile when a supported system needs additional capacity or a replacement for a failed stick. It is not for platforms that require registered DIMMs or speeds beyond 2400 MT/s.

DDR4 2400 UDIMM Limits

The DDR4 2400 interface caps data transfer at PC4-19200 bandwidth, which restricts throughput on memory-intensive workloads compared to faster DDR4 standards. ECC UDIMM topology also limits maximum system capacity because unbuffered modules place a heavier electrical load on the memory controller than registered alternatives. Systems needing higher speeds or larger populations must use a different memory type.

Highlights

  • 16GB DDR4 2400MHz ECC UDIMM for server reliability
  • CL17 latency and 1.20V operation for stable performance
  • 2Rx8 dual-rank design increases memory density
  • 288-pin DIMM fits standard DDR4 server slots
  • Compatible replacement for Dell A9755388, A9755661 and CX1KM

Specifications

BrandA-Tech
Capacity16GB
SpeedDDR4 2400 (PC4 19200)
CAS LatencyCL17
Voltage1.20V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
FeaturesMajor Brand Chips

Questions about this item

Does the 288-pin DDR4 DIMM fit standard unbuffered ECC UDIMM slots?

Yes, the module uses the 288-pin DDR4 DIMM form factor designed for ECC UDIMM slots in compatible servers and workstations.

What is the correct way to seat the 1.2V module so the ECC function initialises?

Align the notch with the slot key, press down firmly until both retention clips click, then verify the system reports 16GB at 2400MHz with ECC active in BIOS.

When should the 2Rx8 rank configuration be rechecked after a firmware update?

Recheck if the server shows reduced capacity, corrected errors increase, or the memory runs below 2400MHz after a BIOS or firmware change.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.