We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two green circuit boards with black memory chips and gold edge connectors

Computer Memory Solutions

Computer Memory Solutions 8GB (2x4GB) DDR3 10600 1333MHz Non-ECC SO-DIMM Dell Precision M4500 memory upgrade

SKU CH-GX74-TRJEB

8GB dual-channel DDR3 1333 MHz SO-DIMM kit validated for Dell Precision M4500 workstations

  • Capacity8GB (2 x 4GB)
  • Type204-Pin DDR3 SO-DIMM
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL7
  • Timing7-7-7
  • Voltage1.5V
  • Guaranteed Dell Precision M4500 compatibility
  • 8 GB total capacity in a matched pair
  • 1333 MHz DDR3 speed for responsive multitasking
  • Low CL7 latency at 1.5 V operation
  • 204-pin SO-DIMM form factor fits factory slots

Dell Precision M4500 memory upgrade

This 8 GB kit is built specifically for the Dell Precision Mobile Workstation M4500. It contains two matched 4 GB modules that install as a pair to enable dual-channel operation. The memory targets owners of that workstation who need the maximum supported capacity for everyday workloads.

8 GB DDR3 1333 MHz capacity and headroom

The kit delivers the full 8 GB ceiling recognised by the M4500, running at DDR3 1333 (PC3 10600) with CL7 timing at 1.5 V. A 32-bit operating system will see only about 3.5 GB, so a 64-bit OS is required to use the complete amount. The two modules must be installed together to reach this limit.

204-pin SO-DIMM form factor for notebook integration

Each stick uses the standard 204-pin DDR3 SO-DIMM layout with no heat spreader, allowing it to fit the tight M4500 memory slots. The unbuffered, non-ECC design matches the workstation's chipset expectations. Installing the pair frees both sockets for the maximum configuration without leaving a single module running in single-channel mode.

Highlights

  • Guaranteed Dell Precision M4500 compatibility
  • 8 GB total capacity in a matched pair
  • 1333 MHz DDR3 speed for responsive multitasking
  • Low CL7 latency at 1.5 V operation
  • 204-pin SO-DIMM form factor fits factory slots

Specifications

BrandComputer Memory Solutions
ModelCM5126410600SODRH
Capacity8GB (2 x 4GB)
Type204-Pin DDR3 SO-DIMM
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL7
Timing7-7-7
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemDell Precision Mobile Workstation M4500
Package Content2 Memory RAM Sticks

Questions about this item

Will the 1333 MHz DDR3 SO-DIMMs run reliably alongside any existing 1333 MHz modules I keep in my Precision M4500?

These modules are rated at DDR3-1333 with CL7 timing. If the installed memory shares the same speed and latency, the system will typically run all sticks at those settings. Mixing different speeds or timings forces the controller to use the slowest common denominator.

How can I verify the kit is operating at the advertised 1333 MHz and CL7 timings after installation?

Open Task Manager or a tool such as CPU-Z and check the memory tab. It should report 1333 MHz (PC3-10600) and 7-7-7 timings at 1.5 V. The BIOS may also show the detected speed and latency during POST.

What exactly is included in the package and is anything else required to complete the upgrade?

The box contains two 4 GB DDR3 204-pin SO-DIMM sticks, giving 8 GB total. No additional parts are needed for the Precision M4500; the modules install directly into the two memory sockets.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.