SK hynix HMA42GR7AFR4N-TF 16GB DDR4 2133MHz CL15 ECC Registered Dual Rank 1.2V 288-Pin Server RAM
- 16GB
- 288-Pin DDR4 SDRAM
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
NEMIX RAM
128 GB DDR5-4800 ECC registered dual-rank kit validated for SuperMicro 211SE servers
This NEMIX RAM kit provides 128GB of DDR5 server memory as two 64GB modules. It runs at 4800MT/s with CL40 latency and operates at 1.10V. The registered ECC design targets SuperMicro IoT SuperServer SYS-211SE platforms and the X31SEED-SF motherboard.
These modules fit systems that require 288-pin registered DDR5 RDIMMs with ECC. They will not work in desktop motherboards or laptops that only accept unbuffered UDIMMs. Buyers needing non-ECC memory or higher speeds should look elsewhere.
The kit uses a 2Rx4 rank configuration on major OEM chips from Samsung, Micron or Hynix. This organisation and the registered buffer are the decisive compatibility factors for the supported SuperMicro 211SE servers.
| Brand | NEMIX RAM |
|---|---|
| Series | SuperMicro Server/Workstation Compatible Series Memory |
| Model | SuperMicro DDR5 4800MHZ ECC RDIMM Registered Server Memory |
| Part Number | MR38400-924K2 |
| Capacity | 128GB (2 x 64GB) |
| Speed | DDR5 4800 (PC5 38400) |
| ECC | Yes |
| Buffered/Registered | Registered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.10V |
| Compatible System | Supermicro |
| CAS Latency | CL40 |
| Heat Spreader | No |
| Type | 288-Pin DDR5 RDIMM |
| Rank | 2Rx4 |
| Features | DDR5 ECC Registered RDIMM Server Motherboard Compatible |
| Package Content | 128GB (2X64GB) DDR5 4800MHZ PC5-38400 2Rx4 1.1V CL40 288-PIN ECC RDIMM Registered Server Memory KIT |
Power down, open the chassis, align each 64GB module's key notch with the DDR5 slot, press firmly until the retention clips click, then verify in BIOS that both 64GB sticks register at 4800 MT/s with ECC active; the step often missed is seating both modules fully so the clips engage on both sides.
No scheduled maintenance is required; the modules run at 1.10 V without heat spreaders, so keep server airflow clean, and replace only if a module fails — ECC corrects single-bit errors on the fly, but a persistent multi-bit fault means swapping the affected 64GB stick.
The CAS latency of CL40 sets the timing floor, so under continuous load the memory controller hits latency-bound throughput before thermal or voltage limits, because the 1.10 V registered DDR5 modules operate within spec without throttling.
Also in this aisle
Same shelf, same checkout — eight coins and a 30-minute rate lock.
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
Pick the language the site speaks to you in.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?