We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two green DDR4 SODIMM sticks, 260-pin, no heat spreader

NEMIX RAM

NEMIX RAM 16GB (2x8GB) DDR4 2400 CL17 260-PIN SODIMM Kit for POSIFLEX XT-6517

SKU CH-XW0S-92B93

DDR4 2400 SODIMM kit adds 16 GB in two 8 GB modules for the POSIFLEX XT-6517 terminal

  • Capacity16GB (2 x 8GB)
  • SpeedDDR4 2400 (PC4 19200)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 16 GB kit boosts multitasking on POSIFLEX XT-6517
  • DDR4 2400 speed matches system specification exactly
  • CL17 latency keeps response tight under load
  • 2 V modules run cool in fanless chassis
  • 260-pin SODIMM form factor fits the terminal slot

Compatible DDR4 2400 SODIMM kit for POSIFLEX XT-6517

This 16 GB kit contains two 8 GB DDR4 2400 modules built for the POSIFLEX XT-6517 terminal. Each stick is a 260-pin 2Rx8 unbuffered SODIMM running at 1.2 V with CL17 timing. It targets IT teams upgrading point-of-sale systems that require this exact density and form factor.

Low-voltage operation with no spreader

The modules draw 1.20 V and have no heat spreader, matching the fanless chassis of the target terminal. Unbuffered non-ECC design keeps the electrical load light for the onboard memory controller. Standard JEDEC DDR4 2400 signalling produces minimal heat under typical POS workloads.

Replaces lower-capacity DDR4 SODIMMs in the same

The kit upgrades terminals currently running with 4 GB or 8 GB of DDR4 2400 memory. The jump is worth it when the OS and POS software together exceed the existing capacity, causing paging or slowdowns during peak hours. It does not fit systems requiring ECC, registered DIMMs, or a different pin count.

Highlights

  • 16 GB kit boosts multitasking on POSIFLEX XT-6517
  • DDR4 2400 speed matches system specification exactly
  • CL17 latency keeps response tight under load
  • 2 V modules run cool in fanless chassis
  • 260-pin SODIMM form factor fits the terminal slot

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 2400MHZ Non-ECC Unbuffered SODIMM
Part NumberMS19200-828K2
Capacity16GB (2 x 8GB)
SpeedDDR4 2400 (PC4 19200)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL17
Heat SpreaderNo
Type260-PIN DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content16GB (2X8GB) DDR4 2400MHZ PC4-19200 2Rx8 1.2V CL17 260-PIN Non-ECC Unbuffered SODIMM KIT

Questions about this item

How do I install the 260-pin SODIMM modules into the POSIFLEX XT-6517 terminal?

Power off the terminal and unplug it. Open the memory compartment, align the notch on each 260-pin DDR4 SODIMM with the slot key, insert at an angle, then press down firmly until the retention clips click on both sides.

What maintenance or replacement will this memory kit need over time?

The modules have no heat spreader and are non-ECC unbuffered; they require no scheduled maintenance. If a module fails, the lifetime replacement warranty covers a direct swap of the defective 8 GB stick.

What limit appears first when the POSIFLEX XT-6517 runs sustained workloads with this DDR4 2400 CL17 kit?

The memory bus tops out at the rated 2400 MT/s speed and CL17 latency; under continuous load the bandwidth ceiling of the DDR4 2400 interface is reached before any thermal throttle occurs on the unbuffered SODIMMs.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.