We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green circuit board with black memory chips, gold edge connector, no heat spreader, SODIMM form factor

NEMIX RAM

NEMIX RAM 16GB DDR4 3200 CL22 260-Pin SODIMM POSIFLEX JK-3232 memory upgrade

SKU CH-X878-XSBQX

16 GB DDR4 3200 CL22 SODIMM for Posiflex JK-3232 kiosks, 1.2 V unbuffered non-ECC

  • Capacity16GB
  • SpeedDDR4 3200 (PC4 25600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 16 GB capacity boosts kiosk multitasking headroom
  • DDR4 3200 speed matches POSIFLEX JK-3232 spec
  • CL22 latency keeps data flow steady
  • 2 V operation cuts power draw and heat
  • 260-pin SODIMM fits the Cachet Series slot exactly

POSIFLEX JK-3232 Memory Upgrade

This NEMIX RAM module delivers 16GB of DDR4 3200 memory in a 260-pin SODIMM form factor. It is built specifically for the POSIFLEX JK-3232 Cachet Series kiosk and operates at 1.2V with CL22 latency. The unbuffered, non-ECC design uses major OEM chips from Samsung, Micron or Hynix.

Kiosk Operators Needing Single-Slot Capacity

The single 16GB stick suits technicians upgrading a POSIFLEX JK-3232 where one slot is free or a full replacement is planned. It is not ECC registered, so it will not meet requirements for servers or workstations that demand error-correcting memory. Buyers needing registered DIMMs or a different pin count should look elsewhere.

Drop-In DDR4 SODIMM for POSIFLEX JK-3232

Installation follows the kiosk service manual and uses the existing SODIMM slot without extra cables or brackets. The 1.2V operation matches the platform's standard DDR4 voltage, leaving the original power budget unchanged. The module frees the second slot when only one is populated, allowing a future 16GB addition.

Highlights

  • 16 GB capacity boosts kiosk multitasking headroom
  • DDR4 3200 speed matches POSIFLEX JK-3232 spec
  • CL22 latency keeps data flow steady
  • 2 V operation cuts power draw and heat
  • 260-pin SODIMM fits the Cachet Series slot exactly

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 3200MHZ Non-ECC Unbuffered SODIMM
Part NumberMS25600-628K1
Capacity16GB
SpeedDDR4 3200 (PC4 25600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL22
Heat SpreaderNo
Type260-Pin DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content16GB (1X16GB) DDR4 3200MHZ PC4-25600 2Rx8 1.2V CL22 260-PIN Non-ECC Unbuffered SODIMM

Questions about this item

Does my POSIFLEX JK-3232 kiosk need any specific BIOS setting or firmware revision before I install this DDR4 3200 CL22 SODIMM?

The module is built to JEDEC DDR4 3200 PC4-25600 1.20V CL22 2Rx8 260-pin SODIMM specification; the kiosk must accept standard non-ECC unbuffered DDR4 SODIMMs at that voltage and speed.

Can I keep an older DDR4 SODIMM in the second slot while adding this 16GB stick?

Both modules must be non-ECC unbuffered DDR4 SODIMMs; the system will run at the lowest common speed and latency, so match voltage (1.20V) and pin count (260) for stability.

How can I verify the stick is recognised at 3200 MT/s with CL22 timing after installation?

Open Task Manager > Performance > Memory or run CPU-Z; confirm speed reads 3200 MT/s, CAS latency shows 22, and capacity reports 16GB (1X16GB).

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.