We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two green DDR4 SODIMM sticks side by side

NEMIX RAM

NEMIX RAM 32GB (2x16GB) DDR4 2400 CL17 260-PIN SODIMM Kit for POSIFLEX XT-6315E

SKU CH-29BX-7JB7W

32 GB DDR4 SODIMM kit (2 × 16 GB) at 2400 MHz CL17 for POSIFLEX XT-6315E terminals

  • Capacity32GB (2 x 16GB)
  • SpeedDDR4 2400 (PC4 19200)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 32GB capacity expands POS terminal multitasking headroom
  • DDR4 2400 speed matches XT-6315E memory bus
  • CL17 latency keeps transaction processing responsive
  • 2V operation reduces fanless system thermal load
  • 260-pin SODIMM form factor fits factory memory slots

Built for POSIFLEX XT-6315E

This 32GB DDR4 SODIMM kit is configured specifically for the POSIFLEX XT-6315E JIVA high-end fanless POS terminal. It delivers 2x16GB modules running at 2400MHz PC4-19200 with CL17 latency. The non-ECC unbuffered design matches the original system requirements for retail and kiosk environments.

Sustained workload stability

Modules are stress tested under load to maintain reliability during continuous operation in fanless terminals. The 1.20V operating voltage and 2Rx8 organisation support steady throughput for transaction processing without thermal throttling. Major OEM chips from Samsung Micron Hynix provide consistent signal integrity over extended shifts.

Straightforward SODIMM upgrade

Installation follows the standard 260-pin SODIMM procedure accessible through the terminal service panel. No heat spreader means modules fit tight clearances in the fanless chassis. The only common issue is seating both modules firmly until the retention clips click, otherwise the system will not recognise the full 32GB capacity.

Highlights

  • 32GB capacity expands POS terminal multitasking headroom
  • DDR4 2400 speed matches XT-6315E memory bus
  • CL17 latency keeps transaction processing responsive
  • 2V operation reduces fanless system thermal load
  • 260-pin SODIMM form factor fits factory memory slots

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR4 2400MHZ Non-ECC Unbuffered SODIMM
Part NumberMS19200-628K2
Capacity32GB (2 x 16GB)
SpeedDDR4 2400 (PC4 19200)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemPOSIFLEX POS
CAS LatencyCL17
Heat SpreaderNo
Type260-PIN DDR4 SODIMM
Rank2Rx8
FeaturesDDR4 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content32GB (2X16GB) DDR4 2400MHZ PC4-19200 2Rx8 1.2V CL17 260-PIN Non-ECC Unbuffered SODIMM KIT

Questions about this item

How much power does the 1.20 V DDR4 kit draw when the POS terminal runs all day?

Each module operates at 1.20 V, the standard DDR4 voltage, so power draw stays low even during continuous operation in the fanless POSIFLEX XT-6315E.

What must the POSIFLEX XT-6315E already have for this 260-pin SODIMM kit to work?

The terminal needs two free DDR4 SODIMM slots that accept 2Rx8 unbuffered non-ECC modules at 2400 MHz.

Will the CL17 2400 MHz modules run stably alongside any original memory left in the XT-6315E?

Yes, the kit is validated for the XT-6315E and will down-clock to match slower installed modules while keeping CL17 timing at 2400 MHz.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.