We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green bare circuit board DDR5 RDIMM memory module with black chips no heat spreader

NEMIX RAM

NEMIX RAM 48GB DDR5 5600MHz CL46 2Rx8 1.1V 288-Pin ECC Registered RDIMM memory upgrade

SKU CH-W0PS-DMP9X

48 GB DDR5 5600 MHz ECC registered RDIMM with CL46 latency and 1.1 V operation, validated for GIGABYTE MA34-CP0 motherboards

  • Capacity48GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 48GB

Show 24 more configurations
  • Registered ECC architecture offloads the controller for stable full-capacity operation
  • 48 GB DDR5 5600 MHz CL46 2Rx8 module delivers rated speed on supported boards
  • 10 V operation matches the server platform's memory voltage requirement
  • 288-pin RDIMM form factor fits the GIGABYTE MA34-CP0 motherboard's DIMM slots
  • Built with major OEM Samsung, Micron or Hynix chips for enterprise-grade reliability

48GB DDR5-5600 ECC Registered RDIMM

This 48GB DDR5-5600 (PC5-44800) registered ECC RDIMM delivers the exact rank, voltage and timing the GIGABYTE MA34-CP0 motherboard expects. The 2Rx8 organisation and 1.10V operation allow the memory controller to recognise full capacity at rated speed. It is built for servers and workstations that require registered DIMMs with error correction.

Sustained-load behaviour

Registered architecture buffers the address and command signals so every slot can run fully populated without overloading the memory controller. ECC detects and corrects single-bit errors on the fly, preventing silent data corruption and unplanned reboots during long compute runs. The module has no heat spreader, so adequate chassis airflow is required to maintain stability under continuous load. Builders who need unbuffered UDIMMs or SODIMMs cannot use this module.

DDR5 interface practical limits

The 288-pin DDR5 RDIMM form factor fits only motherboards designed for registered DDR5 memory. Population order, maximum capacity per slot and supported ranks are defined by the specific platform and must be verified in the system manual before installation. Mixing ranks or voltages not approved by the vendor will prevent the system from booting at the rated 5600MT/s speed.

Highlights

  • Registered ECC architecture offloads the controller for stable full-capacity operation
  • 48 GB DDR5 5600 MHz CL46 2Rx8 module delivers rated speed on supported boards
  • 10 V operation matches the server platform's memory voltage requirement
  • 288-pin RDIMM form factor fits the GIGABYTE MA34-CP0 motherboard's DIMM slots
  • Built with major OEM Samsung, Micron or Hynix chips for enterprise-grade reliability

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-4828K1
Capacity48GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemGIGABYTE
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content48GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN ECC RDIMM KIT

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

How much power does the 1.1 V DDR5 module draw under continuous load?

The kit runs at 1.1 V, the standard DDR5 operating voltage, so power draw stays within the DDR5 specification for registered DIMMs.

Does the GIGABYTE MA34-CP0 motherboard need any specific BIOS setting or firmware revision to recognise this 48 GB RDIMM?

The module is validated for the MA34-CP0 at DDR5-5600; the board must support registered ECC RDIMMs and be populated according to its memory-configuration rules.

Can I mix this 2Rx8 registered ECC stick with older unbuffered non-ECC DDR5 DIMMs in the same server?

No — registered and unbuffered DIMMs cannot be mixed, and ECC requires all installed modules to support error correction for the feature to function.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.