We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green circuit board with black memory chips, gold edge connector, thin rectangular SODIMM module

NEMIX RAM

NEMIX RAM 4GB DDR3 1333 PC3-10600 2Rx8 1.35V 204-PIN SODIMM POSIFLEX XT-5317 memory upgrade

SKU CH-SQ3Y-21V3E

4GB DDR3 SODIMM upgrade for POSIFLEX XT-5317 terminals, 1333 MHz CL9 unbuffered non-ECC

  • Capacity4GB
  • SpeedDDR3 1333 (PC3 10600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.50V
  • 4GB capacity boosts POS terminal responsiveness
  • DDR3 1333 speed matches POSIFLEX XT-5317 requirements
  • 35V low-voltage operation reduces power draw
  • 204-pin SODIMM form factor fits JIVA foldable 17" terminal
  • Tested with Samsung Micron Hynix chips for stability

POSIFLEX XT-5317 compatible DDR3 SODIMM

This 4 GB DDR3 1333 module is built for the POSIFLEX XT-5317 JIVA foldable 17" terminal. It fits the 204-pin SODIMM slot and runs at PC3-10600 speed with CL9 latency. The unbuffered non-ECC design matches the original system specification.

System-specific memory upgrade

The module uses major-brand Samsung, Micron or Hynix chips and is stress-tested under load before shipping. No extra software, heat spreader or cables are included in the package. Installation follows the terminal's own service manual.

Check terminal memory slot and voltage

Verify the XT-5317 has a free SODIMM slot and that the board accepts 1.35 V low-voltage DDR3; the spec sheet also lists 1.50 V so confirm which setting your BIOS uses. This stick is single-rank 2Rx8 and will not work in systems requiring registered or ECC memory.

Highlights

  • 4GB capacity boosts POS terminal responsiveness
  • DDR3 1333 speed matches POSIFLEX XT-5317 requirements
  • 35V low-voltage operation reduces power draw
  • 204-pin SODIMM form factor fits JIVA foldable 17" terminal
  • Tested with Samsung Micron Hynix chips for stability

Specifications

BrandNEMIX RAM
SeriesPOSIFLEX POS Series Point of Sale Kiosk Memory
ModelPOSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM
Part NumberMS10600-428K1
Capacity4GB
SpeedDDR3 1333 (PC3 10600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.50V
Compatible SystemPOSIFLEX POS
CAS LatencyCL9
Heat SpreaderNo
Type204-Pin DDR3 SODIMM
Rank2Rx8
FeaturesDDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content4GB (1X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM

Questions about this item

Will the 204-pin SODIMM slot need any maintenance after installing this 4GB module?

The module has no heat spreader and uses standard 204-pin DDR3 SODIMM contacts, so no periodic maintenance is required once it is seated correctly.

What limits sustained throughput on this PC3-10600 CL9 stick?

The DDR3 1333 MT/s data rate and CL9 latency set the maximum sustained bandwidth for this 4GB 2Rx8 module.

How much heat and power does the 1.35V 4GB SODIMM produce during all-day POS operation?

Rated at 1.35V with no heat spreader, the module draws low power and generates minimal heat in continuous terminal use.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.