We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green circuit board with black memory chips and gold edge connector

NEMIX RAM

NEMIX RAM 8GB DDR3 1600 ECC UDIMM 1.35V 240-Pin Dell C6105 Memory Upgrade

SKU CH-317E-DX1VG

8GB DDR3 1600 ECC UDIMM module at 1.35V for Dell PowerEdge C6105 servers

  • Capacity8GB
  • SpeedDDR3 1600 (PC3 12800)
  • ECCYes
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.35V
  • 8GB capacity expands server memory for virtualization workloads
  • DDR3 1600 speed with CL11 latency processes data efficiently
  • ECC unbuffered design detects and corrects memory errors
  • 35V low voltage reduces power consumption in dense deployments
  • 240-pin UDIMM form factor fits Dell PowerEdge C6105 systems

Dell C6105 ECC UDIMM Upgrade

This 8 GB DDR3 1600 module is built for Dell PowerEdge C6105 servers that require ECC unbuffered memory. It runs at PC3-12800 speed with a low 1.35 V operating voltage and a 240-pin form factor. The single-rank 2Rx8 organisation uses major-brand DRAM chips for stable operation in dense multi-node chassis.

Suited for C6105 maintenance, not other platforms

Administrators expanding or repairing a Dell PowerEdge C6105 will find the correct pin-out, voltage and ECC behaviour guaranteed by the vendor qualification. Builders working on consumer desktops, non-Dell workstations or any system that expects registered DIMMs or standard 1.5 V DDR3 should look elsewhere because the electrical and firmware requirements differ.

1.35 V DDR3 ECC UDIMM decides fit

The module operates at 1.35 V rather than the more common 1.5 V, so the motherboard must explicitly support low-voltage DDR3 ECC unbuffered DIMMs. If the target board only accepts 1.5 V or registered memory, the upgrade will not post. Match the voltage and ECC type exactly before ordering.

Highlights

  • 8GB capacity expands server memory for virtualization workloads
  • DDR3 1600 speed with CL11 latency processes data efficiently
  • ECC unbuffered design detects and corrects memory errors
  • 35V low voltage reduces power consumption in dense deployments
  • 240-pin UDIMM form factor fits Dell PowerEdge C6105 systems

Specifications

BrandNEMIX RAM
SeriesDell Server/Workstation Compatible Series Memory
ModelDell DDR3 1600MHZ ECC Unbuffered UDIMM
Part NumberME12800-828K1
Capacity8GB
SpeedDDR3 1600 (PC3 12800)
ECCYes
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.35V
Compatible SystemDell
CAS LatencyCL11
Heat SpreaderNo
Type240-Pin DDR3 ECC UDIMM
Rank2Rx8
FeaturesDDR3 1600MHZ ECC UDIMM Motherboard Compatible
Package Content8GB (1X8GB) DDR3 1600MHZ PC3-12800 2Rx8 1.35V 240-PIN ECC Unbuffered UDIMM

Questions about this item

Will the 240-Pin DDR3 UDIMM fit the Dell PowerEdge C6105 memory slots?

Yes — the module is a 240-Pin DDR3 ECC UDIMM built to Dell PowerEdge C6105 specifications, so it seats directly in the server's DDR3 DIMM slots.

What is the correct installation step for the 1.35V ECC UDIMM in the C6105?

Power down the server, open the chassis, align the 240-Pin key notch with the slot, press firmly until both latches click, then verify in BIOS that the module shows 8GB at 1600 MT/s with ECC active.

When should the 8GB 2Rx8 DDR3 module be replaced in a C6105?

Replace it if memory diagnostics report uncorrectable ECC errors, the system fails to recognise the full 8GB capacity, or the server cannot maintain stable operation at the rated 1600 MT/s speed.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.