We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green bare circuit board with gold edge contacts and black memory chips

NEMIX RAM

NEMIX RAM 8GB DDR4 2400 ECC RDIMM 1Rx4 CL17 Dell PowerEdge FC430

SKU CH-JVWN-NH6WR

8GB DDR4 2400 ECC registered RDIMM, CL17 1.2V, for Dell PowerEdge FC430 servers

  • Capacity8GB
  • SpeedDDR4 2400 (PC4 19200)
  • ECCYes
  • Buffered/RegisteredRegistered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • ECC protection guards data integrity in Dell PowerEdge FC430
  • Registered DDR4 2400 MHz CL17 meets server timing specs
  • 2 V operation lowers power draw per module
  • 1Rx4 single-rank layout simplifies memory population
  • 288-pin RDIMM form factor fits Dell server slots

Dell PowerEdge FC430 8GB DDR4 ECC RDIMM

This 8GB DDR4 2400 ECC registered DIMM is built for the Dell PowerEdge FC430 server. It targets administrators who need validated, single-rank memory to maintain platform stability under continuous workloads. The module uses major-brand DRAM and runs at 1.2V with CL17 timing.

Upgrade from non-ECC or slower DDR4 in the FC430

Replacing unbuffered or lower-speed modules with this registered ECC kit adds error correction and the 2400 MT/s data rate the FC430 memory controller expects. The jump is worth it when the server shows corrected-error counts or when firmware requires registered DIMMs for full channel population.

Tool-less DIMM slot insertion on the FC430

Installation follows the standard 288-pin RDIMM procedure: open the ejectors, align the notch, press until the latches click. The usual issue is mixing 1Rx4 ranks with different rank configurations in the same channel, which the FC430 BIOS may reject at POST.

Highlights

  • ECC protection guards data integrity in Dell PowerEdge FC430
  • Registered DDR4 2400 MHz CL17 meets server timing specs
  • 2 V operation lowers power draw per module
  • 1Rx4 single-rank layout simplifies memory population
  • 288-pin RDIMM form factor fits Dell server slots

Specifications

BrandNEMIX RAM
SeriesDell Server/Workstation Compatible Series Memory
ModelDell DDR4 2666MHZ ECC RDIMM Registered Server Memory
Part NumberMR19200-814K1
Capacity8GB
SpeedDDR4 2400 (PC4 19200)
ECCYes
Buffered/RegisteredRegistered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemDell
CAS LatencyCL17
Heat SpreaderNo
Type288-Pin DDR4 RDIMM
Rank1Rx4
FeaturesDDR4 ECC Registered RDIMM Server Motherboard Compatible
Package Content8GB (1X8GB) DDR4 2400MHZ PC4-19200 1Rx4 1.2V CL17 288-PIN ECC RDIMM Registered Server Memory

Questions about this item

Does this 288-pin DDR4 RDIMM fit the Dell PowerEdge FC430 memory slots?

Yes, the 288-pin DDR4 RDIMM form factor matches the FC430 memory slots. The module is built for Dell servers and uses the registered ECC design the platform requires.

What is the correct way to seat this registered ECC module, and what step do people often miss?

Align the notch on the 288-pin edge connector with the slot key, press firmly until both retention clips click, and verify the 1Rx4 rank is recognised in the BIOS.

Will the Samsung, Micron or Hynix chips on this 8 GB module need replacement under normal server load?

The major-OEM chips are stress-tested under load and rated for continuous server operation. No scheduled replacement is expected for the life of the system.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.