We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green circuit board SODIMM module with black memory chips and gold edge connector

NEMIX RAM

NEMIX RAM 16GB DDR5 5600MHz CL46 1Rx8 1.1V 262-PIN SODIMM Supermicro X14SAV-TLN4F memory upgrade

SKU CH-BC18-7YQNQ

16 GB DDR5 SODIMM running at 5600 MHz with CL46 timing and 1.1 V, built from major OEM chips and validated for the Supermicro X14SAV-TLN4F motherboard

  • Capacity16GB
  • Type262-Pin DDR5 SODIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 16GB

  • 16 GB DDR5-5600 capacity adds responsive multitasking headroom
  • CL46 timing at 1.1 V runs at rated speed without tuning
  • 1Rx8 single-rank layout matches the memory controller expectations
  • 262-pin SODIMM form factor fits the Supermicro X14SAV-TLN4F slot exactly
  • Major OEM Samsung Micron Hynix chips tested for stability at rated specs

Exact-match 16 GB DDR5 SODIMM for Supermicro

This 16 GB DDR5-5600 module (PC5-44800) uses a 1Rx8 layout, CL46 timing and 1.1 V operation. It arrives as a 262-pin non-ECC unbuffered SODIMM built with major OEM chips from Samsung, Micron or Hynix. The specification matches the memory controller expectations of the Supermicro X14SAV-TLN4F motherboard so the system recognises the full capacity at rated speed.

Replaces slower or smaller DDR5 SODIMMs

If your board currently runs lower-frequency DDR5 or has fewer than 16 GB installed, this module lifts bandwidth and capacity in a single step. The upgrade is worthwhile when the existing memory limits multitasking throughput or forces the controller to down-clock because of rank or voltage mismatch. It will not fit systems that require ECC, registered DIMMs or a different pin count.

Verify your motherboard manual before ordering

Confirm the Supermicro X14SAV-TLN4F supports 16 GB non-ECC unbuffered SODIMMs at DDR5-5600 with 1Rx8 organisation and 1.1 V. Check the approved population order and maximum supported capacity per slot. Ensure the chassis provides access to the SODIMM slots and that no BIOS restriction blocks third-party memory. This module is not suitable for platforms needing ECC, registered memory or a different DDR generation.

Highlights

  • 16 GB DDR5-5600 capacity adds responsive multitasking headroom
  • CL46 timing at 1.1 V runs at rated speed without tuning
  • 1Rx8 single-rank layout matches the memory controller expectations
  • 262-pin SODIMM form factor fits the Supermicro X14SAV-TLN4F slot exactly
  • Major OEM Samsung Micron Hynix chips tested for stability at rated specs

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered SODIMM Memory
Part NumberMS44800-618K1
Capacity16GB
Type262-Pin DDR5 SODIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered SODIMM Motherboard Compatible
Package Content16GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 262-PIN Non-ECC SODIMM KIT

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Does the 262-pin SODIMM fit the Supermicro X14SAV-TLN4F motherboard?

Yes, the module is a 262-pin DDR5 SODIMM built to the exact form factor the Supermicro X14SAV-TLN4F requires. It matches the board's memory-population rules so the controller recognises the full 16 GB at the rated 5600 MHz speed.

What is the correct way to seat the SODIMM in the slot?

Align the notch on the module with the key in the slot, insert at a slight angle, then press down firmly until both side clips snap into the notches. The step people miss is confirming the clips are fully locked; a partially seated stick will cause boot failures or reduced capacity.

Will the memory need any firmware updates or replacement over time?

No firmware updates are required for the RAM itself. The module uses major OEM chips tested for stability at 1.10 V, CL46 and 5600 MHz, and is covered by a lifetime replacement warranty if a defect ever appears.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.