We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green bare circuit board DDR5 memory module with black chips no heat spreader 288 pins

NEMIX RAM

NEMIX RAM 8GB DDR5 5600MHz CL46 1Rx8 1.1V 288-pin UDIMM memory upgrade for Supermicro X13SAE-F

SKU CH-NVMC-GD5JK

8GB DDR5 5600MHz UDIMM with CL46 latency and 1.1V operation, validated for Supermicro X13SAE-F motherboards

  • Capacity8GB
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 8GB

  • Exact-match upgrade for Supermicro X13SAE-F
  • DDR5 5600 speed with CL46 latency
  • 1 V low-voltage operation saves power
  • Major OEM chips tested for stability
  • Lifetime replacement warranty and US support

8GB DDR5-5600 UDIMM for Supermicro X13SAE-F

This 8 GB DDR5 module runs at 5600 MT/s with CL46 latency and 1.10 V operation. It uses a 1Rx8 unbuffered non-ECC design on a standard 288-pin UDIMM form factor. The kit is built specifically for the Supermicro X13SAE-F motherboard and uses major OEM DRAM from Samsung, Micron or Hynix.

Sustained-load behaviour with major OEM chips

Major OEM DRAM from Samsung, Micron or Hynix is tested for stability at the rated 5600 MT/s speed, CL46 timing and 1.10 V voltage. The unbuffered single-rank layout matches the board's memory controller expectations so the module is recognised at full capacity and maintains its rated frequency during extended workloads without throttling.

Replaces slower or smaller DDR5 modules

This kit upgrades a system that currently runs lower-speed DDR5 or has less than 8 GB installed. The jump is worthwhile when the motherboard supports DDR5-5600 and the memory population rules allow a single 1Rx8 UDIMM. It is not suited for builds that require ECC, registered DIMMs or capacities beyond what the X13SAE-F memory slots can accept.

Highlights

  • Exact-match upgrade for Supermicro X13SAE-F
  • DDR5 5600 speed with CL46 latency
  • 1 V low-voltage operation saves power
  • Major OEM chips tested for stability
  • Lifetime replacement warranty and US support

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K1
Capacity8GB
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Does the 1.1V DDR5 module run cool enough for continuous all-day operation?

The stick operates at the standard DDR5 voltage of 1.10V without a heat spreader, so typical case airflow is sufficient for sustained loads.

What motherboard slot and memory controller features are required for this UDIMM to function?

A 288-pin DDR5 UDIMM slot with support for Non-ECC, unbuffered, 1Rx8 modules at 5600MHz and CL46 timing is needed.

Can I add this 8GB stick to an existing bank of DDR5-5600 CL46 modules on the same board?

Yes, provided the motherboard manual confirms the population rules for mixing identical 1Rx8 Non-ECC UDIMMs at the same speed and latency.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.