NEMIX RAM
NEMIX RAM 96GB 6x16GB DDR5 5600MHz CL46 1Rx8 1.1V ECC Registered RDIMM memory upgrade for Supermicro H14SST-G
A 96GB kit of six 16GB DDR5-5600 CL46 1.1V ECC registered RDIMM modules built for the Supermicro H14SST-G motherboard
- Capacity96GB (6 x 16GB)
- Type288-Pin DDR5 RDIMM
- SpeedDDR5 5600 (PC5 44800)
- CAS LatencyCL46
- Voltage1.10V
- ECCYes
- 96 GB total capacity from six 16 GB modules for high-density server workloads
- DDR5 5600 speed with CL46 latency delivers rated throughput for Supermicro H14SST-G
- Registered ECC architecture offloads the memory controller and corrects single-bit errors on the fly
- 1 V operation at 1Rx8 rank matches the board's memory-controller requirements exactly
- 288-pin RDIMM form factor fits the Supermicro H14SST-G motherboard slots precisely
Capacity and configuration
This NEMIX RAM kit provides 96GB of DDR5 memory across six 16GB RDIMMs. Each module is a single-rank 1Rx8 part running at 5600MHz with CL46 latency at 1.1V. The registered ECC design matches the Supermicro H14SST-G motherboard requirements for full-capacity operation.
Suited workloads and limits
The kit targets servers and workstations that need registered ECC memory for data integrity and maximum slot population. It is not for systems that accept only unbuffered UDIMMs or SO-DIMMs, nor for platforms that cannot run registered DIMMs at the rated speed.
Pre-installation checks
Verify the motherboard manual for approved DIMM population order and maximum supported capacity per slot. Confirm the BIOS version supports this memory configuration and that all six slots are available for the registered RDIMM form factor.
Highlights
- 96 GB total capacity from six 16 GB modules for high-density server workloads
- DDR5 5600 speed with CL46 latency delivers rated throughput for Supermicro H14SST-G
- Registered ECC architecture offloads the memory controller and corrects single-bit errors on the fly
- 1 V operation at 1Rx8 rank matches the board's memory-controller requirements exactly
- 288-pin RDIMM form factor fits the Supermicro H14SST-G motherboard slots precisely
Specifications
| Brand | NEMIX RAM |
|---|---|
| Series | NEMIX RAM Original Series Server Memory |
| Model | DDR5 ECC RDIMM Registered Server Memory |
| Part Number | MR44800-618K6 |
| Capacity | 96GB (6 x 16GB) |
| Type | 288-Pin DDR5 RDIMM |
| Speed | DDR5 5600 (PC5 44800) |
| CAS Latency | CL46 |
| Voltage | 1.10V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 1Rx8 |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Heat Spreader | No |
| Compatible System | Supermicro |
| Features | DDR5 ECC RDIMM Motherboard Compatible |
| Package Content | 96GB 6X16GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN ECC RDIMM KIT |
Questions about this item
Does the Supermicro H14SST-G need all six DIMM slots filled for this 96 GB kit to run at DDR5 5600?
The board requires 288-pin RDIMMs and follows its own population rules; installing all six 16 GB modules matches the kit's validated configuration for full-speed operation.
Can I mix these 1Rx8 CL46 registered ECC modules with other DDR5 RDIMMs of different rank or latency?
Mixing ranks, latencies or voltages is not recommended; the motherboard manual specifies approved population order and identical modules ensure stable operation at 5600 MT/s.
How do I confirm the kit is running at 5600 MT/s with ECC active after installation?
Check the BIOS memory information screen or use a tool like dmidecode to verify speed shows 5600 MT/s, capacity reads 96 GB and ECC status reports enabled.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Mushkin Enhanced 4GB DDR2-800 CL6 SoDIMM Apple 971741A memory upgrade
SK hynix HYMD232M646C6-J 256MB DDR 333MHz PC2700 CL2.5 SODIMM laptop RAM
- 4GB (2 x 2GB)



