We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Four green circuit boards with black memory chips and gold edge connectors lying flat

NEMIX RAM

NEMIX RAM DDR5 5600MHz 32GB (4x8GB) CL46 1.1V UDIMM memory upgrade for Supermicro X14SAZ-TLN4F

SKU CH-PBEM-B4975

A 32 GB kit of four 8 GB DDR5 modules running at 5600 MHz with CL46 timing and 1.1 V, validated for the Supermicro X14SAZ-TLN4F motherboard

  • Capacity32GB (4 x 8GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 32GB 4X8GB

  • Ready 32 GB capacity for multitasking with four 8 GB modules
  • DDR5 5600 speed keeps data flowing at PC5-44800 bandwidth
  • Low 1.1 V operation reduces power draw and heat
  • CL46 latency matches board timing for stable boot
  • Verified fit for Supermicro X14SAZ-TLN4F with 288-pin UDIMM form factor

Exact-match DDR5 kit for Supermicro X14SAZ-TLN4F

This 32GB kit delivers four 8GB DDR5 UDIMMs rated at 5600MHz PC5-44800 with CL46 timings at 1.1V. It is built for the Supermicro X14SAZ-TLN4F motherboard and matches the board's required 288-pin unbuffered non-ECC layout. The 1Rx8 rank structure ensures the memory controller recognises full capacity at rated speed.

Low voltage and no spreader keep thermals simple

Operating at 1.1V, the modules draw minimal power and generate little heat during typical desktop workloads. Without a heat spreader, airflow from standard case fans passes directly over the major OEM chips from Samsung, Micron or Hynix. Silent operation is maintained because no active cooling is attached to the memory itself.

Stable under sustained load at rated settings

The kit is tested for stability at its specified 5600MHz speed, CL46 latency and 1.1V voltage during extended use. Consistent throughput is maintained without throttling because the modules run within their validated electrical envelope. Builders who need ECC error correction or registered signalling should choose a different module type.

Highlights

  • Ready 32 GB capacity for multitasking with four 8 GB modules
  • DDR5 5600 speed keeps data flowing at PC5-44800 bandwidth
  • Low 1.1 V operation reduces power draw and heat
  • CL46 latency matches board timing for stable boot
  • Verified fit for Supermicro X14SAZ-TLN4F with 288-pin UDIMM form factor

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K4
Capacity32GB (4 x 8GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB 4X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

How do I install the 4x8GB DDR5 5600 kit into the Supermicro X14SAZ-TLN4F, and what step is often missed?

Power off, open the case, align each 288-pin UDIMM with the slot key, press firmly until both clips lock, then populate all four slots in the order the motherboard manual specifies; the step most often missed is following that exact population sequence, which lets the memory controller train at 5600 MT/s with CL46 at 1.1 V

What maintenance or replacement will the 32 GB DDR5 kit need over time?

No scheduled maintenance is required; the modules have no heat spreader or moving parts, so only a rare complete failure would call for a replacement under the lifetime warranty

Which limit appears first when the Supermicro X14SAZ-TLN4F runs this 5600 MT/s DDR5 kit under sustained load?

The memory controller locks to the JEDEC 5600 MT/s CL46 1.1 V profile, so the first ceiling you hit is the rated speed and latency — no higher frequency or tighter timing is supported without overclocking, which this unbuffered non-ECC kit is not validated for

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.