We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green rectangular circuit board with gold edge connector and black memory chips

OWC

OWC 4GB DDR3 1333 CL9 1.5V 204-pin SODIMM memory upgrade

SKU CH-MBNB-RE0S5

A single 4GB DDR3 1333 CL9 1.5V SODIMM module for HP ProBook 4230s, 4310s, 4320s, 4325s and 4326s laptops

  • Capacity4GB
  • Type204-Pin DDR3 Non-ECC SODIMM
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL9
  • Voltage1.5V
  • ECCNo
  • Boosts multitasking with 4GB DDR3 1333MHz CL9 SODIMM
  • Fits HP ProBook 4230s 4310s 4320s 4325s 4326s
  • JEDEC and RoHS compliant for warranty-safe upgrades
  • Simple DIY install with 204-pin unbuffered design
  • Lifetime warranty backed by OWC tech support

Single-module 4 GB DDR3 SODIMM

This 204-pin DDR3 module delivers 4 GB at 1333 MHz with CL9 latency and 1.5 V operation. It is built to JEDEC and RoHS standards and validated for the HP ProBook 4230s, 4310s, 4320s, 4325s and 4326s. The unbuffered, non-ECC design installs without tools in most compatible notebooks.

Suits owners of listed ProBooks needing

Builders who require ECC, registered DIMMs, a different voltage or a higher capacity per module should look elsewhere. Systems that only accept 1.35 V low-voltage DDR3 cannot use this stick. The 2Rx8 rank layout may not work in platforms limited to single-rank modules.

2Rx8 rank configuration

The module uses a dual-rank 2Rx8 organisation, which determines whether the memory controller can address the full 4 GB. Check the service manual for your specific ProBook model to confirm dual-rank support before purchase.

Highlights

  • Boosts multitasking with 4GB DDR3 1333MHz CL9 SODIMM
  • Fits HP ProBook 4230s 4310s 4320s 4325s 4326s
  • JEDEC and RoHS compliant for warranty-safe upgrades
  • Simple DIY install with 204-pin unbuffered design
  • Lifetime warranty backed by OWC tech support

Specifications

BrandOWC
Part Number1S3D32R804GB
Capacity4GB
Type204-Pin DDR3 Non-ECC SODIMM
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL9
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemHP ProBook 4230s
HP ProBook 4310s
HP ProBook 4320s
HP ProBook 4325s
HP ProBook 4326s

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Which HP ProBook models must I own for this 204-pin DDR3 1333 CL9 SODIMM to be compatible?

The module is validated for HP ProBook 4230s, 4310s, 4320s, 4325s and 4326s, so one of those laptops is required for a supported installation.

Will this 1.5 V PC3-10600 module work alongside the original memory already in my ProBook?

Yes, it is an unbuffered non-ECC DDR3 SODIMM at the same voltage and speed, so it can run in dual-channel with the factory-installed sticks.

How can I confirm the 4 GB upgrade is running at DDR3 1333 CL9 after installation?

Open Task Manager or a system-information utility and verify the memory speed shows 1333 MHz with CAS latency 9 for the new module.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.