我們接受加密貨幣付款 — 讓您持有的幣種也能買到真正的硬體設備。以加密貨幣付款，直接購入真正的硬體設備。 全球訂單滿 US$399，即享免費保險運送。簡約外箱，不印任何品牌標誌，從德國出貨。訂單滿 US$399，即享免費保險運送。 結帳一開始，您的匯率即鎖定 30 分鐘。匯率鎖定 30 分鐘。 每件商品皆原廠密封、序號經過核對，並享有 24 個月保固。原廠密封，保固 24 個月。

追蹤清單 登入
Two green circuit boards with black chips, no heat spreaders

NEMIX RAM

NEMIX RAM 16GB (2 x 8GB) DDR5 5600 CL46 1.1V 288-pin UDIMM Kit for Supermicro X13SAW-F

SKU CH-V8FT-2DPD5

A 16 GB (2 x 8 GB) DDR5 5600 CL46 1.1 V 288-pin UDIMM kit verified for the Supermicro X13SAW-F motherboard

  • Capacity16GB (2 x 8GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 16GB 2X8GB

  • Exact-match DDR5-5600 kit installs at rated speed without manual tuning
  • 16 GB dual-channel capacity lifts multitasking headroom for demanding workloads
  • Low 1.1 V operation reduces power draw and heat output
  • Major OEM chips from Samsung, Micron or Hynix deliver verified stability
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F memory slots exactly

16 GB DDR5 Kit for Supermicro X13SAW-F

This 16 GB kit contains two 8 GB DDR5 5600 UDIMMs built for the Supermicro X13SAW-F motherboard. Modules run at 1.10 V with CL46 latency and a 1Rx8 layout. The 288-pin unbuffered non-ECC design matches the board's native memory specification exactly.

Who this suits and who it does not

Ideal for owners of a Supermicro X13SAW-F board who need a direct, spec-matched 16 GB DDR5 upgrade. Not suitable for systems that require ECC registered DIMMs, SODIMM form factors, speeds above 5600 MT/s, or capacities beyond 16 GB per kit.

The deciding specification

The board requires 288-pin DDR5 UDIMMs at 5600 MT/s, 1.10 V, CL46, non-ECC, unbuffered, 1Rx8. This kit matches every one of those values, so the memory controller recognises the full capacity at rated speed without manual tuning.

商品特色

  • Exact-match DDR5-5600 kit installs at rated speed without manual tuning
  • 16 GB dual-channel capacity lifts multitasking headroom for demanding workloads
  • Low 1.1 V operation reduces power draw and heat output
  • Major OEM chips from Samsung, Micron or Hynix deliver verified stability
  • 288-pin UDIMM form factor fits the Supermicro X13SAW-F memory slots exactly

商品規格

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-818K2
Capacity16GB (2 x 8GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB 2X8GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

其他版本

同系列還有 5 款

同系列產品，記憶體、散熱器或時脈不同 — 下單前請先比較。

商品問答

Does the Supermicro X13SAW-F need any specific DIMM population order for this 16GB (2 x 8GB) kit?

The motherboard manual lists the supported capacities and approved DIMM population order; follow those steps so the 288-pin UDIMM kit is recognised at full 16GB capacity and runs at DDR5 5600.

Will this DDR5 5600 CL46 1.10V kit run at its rated speed if I keep older DDR5 modules installed alongside it?

Mixing modules with different speeds, timings or voltages usually forces the memory controller to run all sticks at the lowest common settings, so the kit may not hold DDR5 5600 CL46 when paired with dissimilar memory.

How can I verify the kit is operating at DDR5 5600 CL46 after installation?

Check the memory speed and timings in the BIOS or a system-information tool; it should report 5600 MT/s and CAS latency 46 at 1.10V when the XMP or default profile is active.

同類商品

顧客也比較過

同一分類，同一套結帳流程 — 支援八種加密貨幣，匯率鎖定 30 分鐘。