OWC 8GB DDR4 3200MHz CL22 1.2V 288-pin UDIMM memory upgrade
- 8GB
- 288-Pin DDR4 Non-EC…
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
OWC
8GB DDR4 2666 ECC UDIMM with CL19 latency and 1.2V operation, validated for QNAP TS-h1283XU-RP, TS-h1683XU-RP, TS-h2483XU-RP, TS-h686 and TS-h886 NAS systems
This 8GB DDR4 2666 CL19 ECC unbuffered module is built for QNAP TS-h1283XU-RP, TS-h1683XU-RP, TS-h2483XU-RP, TS-h686 and TS-h886 systems. It adds capacity while maintaining data integrity through error-correcting code. The single-rank 1Rx8 design fits standard 288-pin DIMM slots. It replaces QNAP part number RAM-8GDR4ECT0-UD-2666 directly.
The module operates at 1.2 volts and meets JEDEC PC4-21300 specifications for broad compatibility. It is backward compatible with 2133MHz and 2400MHz bus speeds. The bare circuit board allows installation in tight NAS chassis where tall heat spreaders would block adjacent slots or airflow. No extra power connectors or tools are required for the upgrade.
Confirm the exact model number matches the supported list above. Check how many memory slots your unit has populated and the maximum capacity per slot allowed by the firmware. Ensure the system accepts unbuffered ECC UDIMMs rather than registered or load-reduced variants. This module is not suitable for platforms that require registered memory or non-ECC consumer DIMMs.
| Brand | OWC |
|---|---|
| Part Number | 2E6D41R808GB |
| Capacity | 8GB |
| Type | 288-Pin DDR4 ECC UDIMM |
| Speed | DDR4 2666 (PC4 21300) |
| CAS Latency | CL19 |
| Voltage | 1.2V |
| ECC | Yes |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx8 |
| Heat Spreader | No |
| Compatible System | QNAP TS-h1283XU-RP QNAP TS-h1683XU-RP QNAP TS-h2483XU-RP QNAP TS-h686 QNAP TS-h886 |
Other versions of this model
Same family, different memory, cooler or clock — compare before you commit.
The module is rated for 2666 MHz PC4-21300 CL19 at 1.2 V; the listed QNAP models accept this speed natively, so it will operate at the full 2666 MHz data rate.
Yes, the stick uses the standard 288-pin UDIMM form factor with no heat spreader, matching the slot keying and height clearance of the TS-h686 and TS-h886 NAS units.
Power off the NAS, open the chassis, align the notch on the 288-pin edge connector with the slot key, press firmly until both retention clips click, then power on and verify 8 GB in the system information.
Also in this aisle
Same shelf, same checkout — eight coins and a 30-minute rate lock.
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
Pick the language the site speaks to you in.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?