OWC 16GB DDR3 1333 PC3-10600 CL9 2Rx4 240-pin 1.5V ECC Registered RDIMM
- 16GB
- 240-Pin DDR3 ECC RD…
We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.
OWC
Adds 16 GB of DDR3 ECC registered memory at 1333 MHz for Dell PowerEdge R920, T410, T610 and T710 servers
Capacity 16GB
This 16GB DDR3 ECC registered DIMM is built for Dell PowerEdge R920, T410, T610 and T710 servers. It runs at 1333MHz with CL9 latency and 1.5V operation. The module uses a 2Rx4 rank configuration on a 240-pin interface. It is not compatible with standard desktop computers or unbuffered memory.
The module operates at the standard 1.5V DDR3 voltage without a heat spreader. Registered buffering reduces electrical load on the memory controller during sustained workloads. ECC circuitry adds minimal overhead while correcting single-bit errors. Power draw stays within JEDEC limits for PC3-10600 modules.
The bare green PCB fits directly into 240-pin DDR3 slots on the listed PowerEdge models. Registered signalling requires a compatible server chipset to function. Mixing with unbuffered DIMMs will prevent boot. The single-module design allows incremental capacity increases up to the system maximum.
| Brand | OWC |
|---|---|
| Part Number | 1R3D32R416GB |
| Capacity | 16GB |
| Type | 240-Pin DDR3 ECC RDIMM |
| Speed | DDR3 1333 (PC3 10600) |
| CAS Latency | CL9 |
| Voltage | 1.5V |
| ECC | Yes |
| Buffered/Registered | Registered |
| Rank | 2Rx4 |
| Heat Spreader | No |
| Compatible System | Dell PowerEdge R920 Dell PowerEdge T410 Dell PowerEdge T610 Dell PowerEdge T710 |
Other versions of this model
Same family, different memory, cooler or clock — compare before you commit.
Power off the server, open the chassis, align the notch on the 240-pin module with the slot key, press firmly until both latches click, then verify in BIOS that the 16GB module is recognised at 1333MHz. The step often missed is confirming the memory mode supports registered DIMMs and not mixing with unbuffered modules.
No scheduled maintenance is required for the module itself. Keep server air filters clean so the 1.5V DIMM stays within thermal limits. Replacement is only needed if a memory error persists after reseating, or when total capacity must exceed the slot limit of the R920, T410, T610 or T710 platform.
The memory controller’s maximum supported frequency of 1333MHz (PC3-10600) is the first ceiling; the module will not run faster. Beyond that, the 2Rx4 organisation and registered buffer add slight latency, so sustained bandwidth is capped by the DDR3 1333 interface rather than the 16GB capacity or 1.5V supply.
Also in this aisle
Same shelf, same checkout — eight coins and a 30-minute rate lock.
What you pay in, and what you read prices in.
Sent from your wallet at checkout
Display only — the catalogue is priced in USD
No currency matches that.
Pick the language the site speaks to you in.
No language matches that.
New here?
Already have one?
There is no automatic reset: this shop sends no mail, so there is no one-time link to ask for. Leave the address on the account and it gets picked up by hand.
Request noted
Nothing is on its way to your inbox — this shop sends no mail at all. Someone picks these up by hand.
Remembered it?